Ryobi AR46000 Manuel d'utilisateur télécharger pdf

WARNING:

To reduce the risk of injury, user must read and understand

the operator’s manual for their chain saw and this instruction

sheet. Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Ensure compatibility and fit before

using any accessory. Do not use an accessory if a part is dam-

aged or missing. If you are not comfortable performing any of

the functions described in these instructions, take your unit to

an authorized service center.

WARNING:

Before installing the new air filter, spark plug, fuel filter, and/or

primer bulb, shut off engine, wait for all moving parts to stop,

allow engine to cool, drain any remaining fuel from tank into

approved fuel container, press the primer bulb several times to

remove any remaining fuel, then disconnect spark plug wire and

move it away from spark plug. Failure to follow these instructions

can result in serious personal injury or property damage.

WARNING:

Gasoline and its vapors are highly flammable and explosive. To

prevent serious personal injury and property damage, handle it

with care. Keep away from ignition sources, open flames, and

sparks, handle outdoors only, do not smoke and wipe up spills

immediately.

PACKING LIST:

Primer bulb Spring clamp

Air filter Spark plug

Fuel filter

The following instructions apply only to HOMELITE chain saws

with 45cc or 46cc engines and RYOBI chain saws with 46cc

engines.

INSTALLING A NEW AIR FILTER

See Figures 1 - 3.

nActivate chain brake by pushing the front hand guard/chain

brake forward toward the bar.

nPull the choke lever out.

nRemove the three screws holding the cylinder cover.

nLift the front of the cylinder cover past chain brake.

nLift the back of the cylinder cover past the handle.

nBefore removing the air filter from the carburetor, blow or brush

as much loose dirt and sawdust from around the carburetor and

chamber as possible.

nRemove the screw securing the old air filter.

nPosition a flat screwdriver between the tabs and twist to release

from the air filter base.

nLift the old air filter off the air filter base and discard.

nInstall the new air filter and reassemble the chain saw.

CAUTION:

Make sure the air filter is correctly replaced before reassembly.

Never run the engine without the air filter, as this may cause

serious damage to the chain saw.

INSTALLING A NEW SPARK PLUG

See Figure 4 - 5.

nRemove the screws and cylinder cover as described previously.

nRemove the spark plug cap.

nLoosen the old spark plug by turning it counterclockwise with

a torque wrench.

45cc and 46cc CHAIN SAW TUNE UP KIT

AR46000

nRemove the old spark plug.

nHand thread the new spark plug, turning it clockwise. Torque

spark plug to 150 in-lbs to secure. Then reassemble saw.

NOTE: Be careful not to cross-thread the spark plug. Cross-

threading will seriously damage the cylinder.

The engine uses a Champion RCJ-4 with .025 in. electrode gap.

Use an exact replacement and replace every 50 hours of use or

more frequently, if necessary.

INSTALLING A NEW PRIMER BULB

See Figure 6.

nDrain all fuel from fuel tank into a container approved for gaso-

line.

NOTE: Squeeze primer bulb several times to purge fuel from

carburetor.

nRemove the screws and cylinder cover as described previously.

nTurn the saw so that the primer bulb is facing you.

To remove the old primer bulb:

nDepress latches on both sides of the old primer bulb and remove

it from base.

nDisconnect the primer line and return fuel line from the old primer

bulb.

NOTE: The primer line is the fuel line that connects the primer

bulb to the carberator.

To install the new primer bulb:

nConnect return line to the large fitting on the new primer bulb

and attach primer line to the small fitting.

nInstall new primer bulb onto the base, ensuring that it latches

securely in place, and reassemble the saw.

WARNING:

Check for fuel leaks after completing installation of primer

bulb. Any part that is leaking fuel is a fire hazard and must

be replaced or reinstalled immediately. If you find any leaks,

correct the problem before using the product. Failure to do so

could result in a fire that could cause serious personal injury.

INSTALLING A NEW FUEL FILTER

See Figure 7.

nDrain all fuel from tank into a container approved for gasoline.

nTurn the saw so that the fuel cap is facing you.

To remove the old fuel filter:

nRemove the fuel cap.

nPull the fuel line and old fuel filter out of the tank. Be carefull

not to disconnect the fuel line from the carburetor.

NOTE: It may be helpful to use needle nose pliers to pull the

fuel line and old fuel filter to the outside of the tank.

nCut the fuel line just below the spring clamp. Allow the old fuel

filter and old spring clamp to air dry and discard in accordance

with all Federal, State, and Local laws and regulations.

To install the new fuel filter:

nPlace the new spring clamp onto the fuel line.

nPush the end of the new fuel filter securely into the fuel line.

nSlide the new spring clamp over the fuel line and new fuel filter

to secure the filter in place.

NOTE: The spring clamp has a wide and a narrow end. The

wide end should rest over the fuel filter.

nPlace fuel line and new fuel filter into the tank. Make sure the

filter rests in the lowest point of the fuel tank.

nSecurely replace fuel cap.

WARNING:

Check for fuel leaks. A leaking fuel cap is a fire hazard and

must be replaced immediately. If you find any leaks, correct the

problem before using the product. Failure to do so could result

in a fire that could cause serious personal injury.

A - Screw (vis, tornillo)

B - Air filter (filtre à air, filtro de aire)

Fig. 1

STOP

A - Screws (vis, tornillos)

B - Cylinder cover (couvercle du cylindre, tapa del cilindro)

C - Front hand guard/ chain brake (protection de poignée avant/frein de

chaîne, protección delantera de la mano/freno de la cadena)

D - Front handle (poignée avant, mango delantero)

Fig. 4

A - Spark plug (bougie, bujía)

B - Spark plug cap (creux de la bougie, tapa ce la bujía)

A - Primer bulb (poire d’amorçage, bomba de cebado)

B - Primer line (primer line, primer line)

C - Return fuel line (conduit à essence de retour, conducto de retorno de

combustible)

D - Latches (conduit à essence de retour, conducto de retorno de

combustible)

E - Large fitting (grande raccord, conexión grande)

F - Small fitting (petit raccord, conexión pequeña)

Fig. 6

Fig. 7

A - Fuel filter (filtre de carburant, filtro de combustible)

B - Fuel line (conduit à essence, conducto de combustible)

C - Fuel cap (bouchon de carburant, tapa del tanque)

D - Spring clamp (bride à ressort, prensa de resorte)

STOP

988000-304

10-28-10 (REV:02)

Fig. 3

Fig. 5

A - Torque wrench (clé dynamométrique, llave dinamométrica )

Fig. 2

A - Choke lever (levier de volet de départ, palanca del anegador)

1 2

Résumé du contenu

Page 1

WARNING:To reduce the risk of injury, user must read and understand the operator’s manual for their chain saw and this instruction sheet. Always wear

Page 2 - MOTOSIERRA DE 45 cc y 46 cc

AVERTISSEMENT :Pour réduire les risques de blessures, l’utilisateur doit lire et veiller à bien comprendre le manuel d’utilisation du scie à chaine ai

Commentaires sur ces manuels

Pas de commentaire

Ryobi AR46000 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour la vidéo Ryobi AR46000. Ryobi AR46000 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour la vidéo Ryobi AR46000