Ryobi EHT0001 Manuel d'utilisateur télécharger pdf

OPERATOR’S MANUAL

SonicTape Distance Finder

EHT0001

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your SonicTape Distance Finder has been engineered and manufactured

to our high standards for dependability, ease of operation, and operator

safety. When properly cared for, it will give you years of rugged, trouble-free

performance.

WARNING: To reduce the risk of injury, the user must read and

understand the operator’s manual before using this product.

Thank you for your purchase.

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all

instructions listed below, may result in electric shock, fire and/or serious

personal injury.

CAUTION:

Use of controls or adjustments or performance of procedures other than

those specified herein may result in hazardous radiation exposure.

CAUTION:

The use of an optical instrument with this product will increase eye

hazard.

The laser guide radiation used in this product is Class II with < 1mW and

650 nm wavelengths. These lasers do not normally present an optical hazard

although staring at the beam may cause flash blindness.

 Avoid direct eye exposure when using the laser and do not project

the laser beam directly into the eyes of others. Serious eye injury could

result.

 Do not remove or deface any product labels. Removing product labels

increases the risk of exposure to laser radiation.

 Do not use the product in a position that may cause anyone to stare

into the laser beam intentionally or unintentionally. Serious eye injury

could result.

 Do not operate the product around children or allow children to oper-

ate the product. Serious eye injury could result.

 Do not operate the product in combustible areas such as in the pres-

ence of flammable liquids, gasses, or dust.

 Always ensure the laser beam is aimed at a surface without reflective

properties. Shiny reflective materials are not suitable for laser use.

 Handle the product with care. Treat it as you would any other optical

device such as a camera or binoculars.

 Avoid exposing the product to shock, continuous vibration, or extreme

hot or cold temperatures. Damage to the product and/or serious injury

to the user could result.

Save these instructions. Refer to them frequently and use them to instruct

others who may use this product. If you loan someone this product, loan

them these instructions also.

SAFETY RULES

NOTE: Before operating the product for the first time, remove and discard

the plastic strip protruding from the battery compartment. Also, remove hang

tag and store with operating instructions for future reference.

The SonicTape Distance Finder is designed to measure distances accurately,

easily, and quickly.

NOTE: Measurements are calculated from the battery compartment cover.

Turning the distance finder on and off:

To turn the distance finder on or off, depress both the area and the distance

buttons simultaneously and hold for several seconds.

To measure distance:

 Position the product so the laser lens is square to the target object, then

press and release the distance button to make a single measurement.

 For continuous measuring, press and hold the distance button as you

move to different target areas.

To calculate area:

 Position the product so the laser lens is square to the first target object;

press and release the distance button to make the first measurement.

 Press and release the area button. Area ( ) will show briefly in the

LCD display, then your first measurement with display again.

 Press and release the distance button to measure distance to the sec-

ond target object. The measurement may be taken more than once, if

needed.

 Press and release the area button again to calculate area.

To clear old measurements or error (

) conditions, do one of the

following:

 Take another measurement.

 Press and hold the area button for several seconds to reset.

OPERATING TIPS

 Any object that is within a maximum angle of ± 5º of the target zone will

be recognized as a target and will be taken into account in the measure-

ment that is displayed.

 It is easier to obtain an exact measurement when measuring the distance

to a wide, flat, straight surface. Other surfaces may cause the distance

finder to display an error.

 The target area should not be a small surface, irregular shape, or absorb-

ing material. If it is, place a piece of cardboard at the target location and

measure to that surface instead.

 The distance finder cannot measure through glass.

 To change the unit of measurement from feet/inches to meters, depress

the unit button.

 Always keep your fingers clear of the sonic cone.

OPERATION

PRODUCT SPECIFICATIONS

Operating Temperature..............................................................32˚F to 104˚F

Measurement Range ............................................................ 12 in. to 32.8 ft.

Accuracy ............................................................................................± 0.5%

Power Supply ..................................................................... 4 SR44 Batteries

Dimensions ................................................................... 2 in. x 1.25 in. x 2 in.

Weight ...............................................................................................1.75 oz.

FEATURES

987000-178

7-26-07 (REV:01)

UNIT

BUTTON

BaTTery

cOmparTmeNT

cOver

BaTTery

cOmparTmeNT

CHANGING THE BATTERIES

Change all four batteries when the low battery symbol ( )is displayed.

 Remove the cover from the battery compartment.

 Remove used batteries and discard according to your local regulations.

 Install four new SR44 button cell batteries according to polarity indicated

inside battery compartment.

 Replace battery compartment cover.

ALWAYS BE AWARE of the location where

the laser light is emitted when using the

distance finder. ALWAYS MAKE SURE

that any bystanders in the vicinity of use

are made aware of the dangers of looking

directly into the laser beam.

WAVE LENGTH: 650nm Max

MAX. POWER OUTPUT < 1mW

CLASS II LASER PRODUCT

AVOID EXPOSURE- Laser Radiation Emitted from this Aperture

MODEL NO. EHT0001

Complies with 21 CFR parts

1040.10 and 1040.11

LASER RADIATION - AVOID DIRECT EYE RADIATION

LcD

DISpLay

area

BUTTONDISTaNce

BUTTON

LaSer

LeNS

SONIc

cONe

1 2

Résumé du contenu

Page 1 - SonicTape Distance Finder

OPERATOR’S MANUALSonicTape Distance FinderEHT0001SAVE THIS MANUAL FOR FUTURE REFERENCEYour SonicTape Distance Finder has been engineered and manufactu

Page 2 - MEDIDOR DE DISTANCIA

MANUAL DEL OPERADORMEDIDOR DE DISTANCIA SÓNICOEHT0001GUARDE ESTE MANUAL PARA FUTURAS CONSULTASSu medidor de distancia sónico ha sido diseñado y fabric

Commentaires sur ces manuels

Pas de commentaire

Ryobi EHT0001 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour la vidéo Ryobi EHT0001. Ryobi EHT0001 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour la vidéo Ryobi EHT0001