Ryobi YG601PV1 Manuel d'utilisation et d'entretien télécharger pdf (Page 11)

11 – English

CONNECTING/DISCONNECTING AIR HOSE

See Figure 2, page 16.

WARNING:

Never exceed the air tool’s pressure rating as recom-

mended by the manufacturer. When using this air com-

pressor as an inflation device, always follow the maximum

inflation guidelines stated by the manufacturer of the item

being inflated.

 Make sure the air compressor is off and unplugged.

 Rotate pressure regulator knob fully in the counter-

clockwise direction so that the outlet pressure is at

zero (0) psi.

 Attach an air hose with 1/4 in. NPT quick-connect air fitting

to a quick connect coupler (1/4 in.) on air compressor.

Make sure to push the air fitting fully into the coupler until

the sleeve springs forward to lock in place.

 To lessen the chance of the air compressor becoming

unbalanced during use, route the air hose through the

corresponding hose channel on the bottom of the unit,

out the nearest side, then over to your worksite.

To disconnect an air hose or an air tool:

 Confirm that the outlet pressure is at zero (0) psi.

 When disconnecting a hose from quick connect coupler

(1/4 in.), always firmly hold fitting end of hose.

 Push back on the release sleeve on the 1/4 in. quick-

connect coupler.

 With a firm grip, pull out the quick-connect air fitting that

is attached to the quick connect coupler.

BREAK-IN PERIOD

Before first use, run the air compressor at zero (0) tank pres-

sure with the drain valve fully open for 30 minutes.

TURNING THE AIR COMPRESSOR ON/OFF

See Figure 3, page 17.

 With the air compressor plugged in, turn the on/off switch

to the ON position to power the compressor on.

 To turn the air compressor off, turn the on/off switch to

the OFF position.

NOTE: When the compressor is in the ON position, the

air compressor will automatically turn back on when the

designated tank air pressure drops below the preset pressure

limit. It will also shut off again when the desired pressure

is reached.

WARNING:

Never exceed the air tool’s pressure rating as recom-

mended by the manufacturer. When using this air com-

pressor as an inflation device, always follow the maximum

inflation guidelines stated by the manufacturer of the item

being inflated.

WARNING:

Always ensure the switch is in the OFF (O) position and

the regulator pressure gauge reads zero before changing

air tools or disconnecting the hose from the air outlet.

Failure to do so could result in possible serious personal

injury.

USING THE AIR COMPRESSOR

See Figure 4, page 17.

WARNING:

Risk of bursting. Do not adjust pressure regulator

knob to result in output pressure greater than marked

maximum pressure of attachment and/or the item being

inflated. Never use at pressure greater than 150 psi. Fail-

ure to heed this warning could result in possible serious

personal injury.

WARNING:

Air powered tools may require more air consumption

than this air compressor is capable of providing. Check

the tool manual to avoid damage to the tool or risk of

personal injury.

 Attach air hose following the instructions in Connecting/

Disconnecting Air Hose (Not Provided).

 Set the amount of air pressure desired using the pressure

regulator knob. Pull the knob up, then turn clockwise to

increase or counterclockwise to decrease the air pressure

to be provided through the hose. When the desired

pressure is set, push the knob back down to lock.

NOTE: Always use the minimum amount of pressure

necessary for your application. Using a higher pressure

than needed will drain air from the tank more rapidly and

cause the unit to cycle on more frequently.

 When finished, always drain the tank and unplug the

unit. Never leave the unit plugged in and/or running

unattended.

OPERATION

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 17 18

Commentaires sur ces manuels

Pas de commentaire

Ryobi YG601PV1 Manuel d'utilisation et d'entretien Page 11

Commentaires sur ces manuels