Ryobi YN301PL1 Manuel de l'opérateur télécharger pdf (Page 12)

12 - English

OPERATION

TRANSPORTING THE AIR COMPRESSOR UP

OR DOWN STAIRS

See Figure 5, page 17.

To transport the air compressor down stairs:

 Using the carrying handle get a firm grasp of the unit. Lift

the unit into a safe and comfortable carrying position.

NOTE: Use good lifting techniques and get help if

needed.

 With proper footing and balance, carry the unit down one

step at a time.

 Use care in transporting the unit down or up stairs to avoid

damage to the stairs, damage to the unit, and personal

injury.

 Lower the air compressor until it sits securely on a flat

surface.

TOOL STORAGE

See Figure 6 - 7, page 17.

 Pneumatic accessories may be stored in the accessory

compartment.

NOTE: Always disconnect the tools from the air hose

and securely close the accessory compartment before

storage.

 Certain pneumatic nailers can be mounted to the sides

of the air compressor using the side connect storage

areas. Framing and roofing nailers should not be stowed

in these storage areas as they are too large.

NOTE: Never rest the trigger of the nailer/stapler tool on

this storage mount.

 The air compressor should be stored on a stable flat

surface either in the horizontal or upright position.

NOTE: Do not suspend the air compressor as it may result

in damage to the air compressor or personal injury.

AUTO/OFF

See Figure 8, page 17.

 Connect the air compressor to a power supply. Turn

the power switch to the AUTO position to power the

compressor on, as shown in the start up section of the

quick reference label.

NOTE: Do not run the compressor in the vertical position.

 To turn the air compressor off, turn the power switch to

the OFF position.

NOTE: When the compressor is in the AUTO position, the

air compressor will automatically turn back on when the tank

air pressure drops below the preset pressure limit. It will also

shut off again when the max pressure is reached.

RESETTING THE COMPRESSOR

When amperage into the air compressor exceeds the specified

amperage, the air compressor will automatically shut off.

To reset the air compressor:

 Turn the air compressor off.

 Unplug the air compressor to allow unit to cool and to

trigger reset.

NOTE: If the overload protector is actuated, the motor

must be allowed to cool down for 30 minutes.

 Plug the air compressor into an approved outlet.

 Turn the air compressor on.

WARNING

Never exceed the air tool’s pressure rating as

recommended by the manufacturer. When using this

air compressor as an inflation device, always follow the

maximum inflation guidelines stated by the manufacturer

of the item being inflated.

WARNING

Always ensure the switch is in the OFF position and

the regulator pressure gauge reads zero (0) psi before

changing air tools or disconnecting the hose from the air

outlet. Failure to do so could result in possible serious

personal injury.

CONNECTING/DISCONNECTING HOSES TO

THE AIR COMPRESSOR

See Figures 8 - 10, pages 17 - 18.

When connecting a pneumatic air nailer or other air tool

always follow the manufacturer’s recommended start-up

procedure.

When connecting/disconnecting a hose to the air compressor

always do the following:

 Ensure AUTO/OFF switch is in the OFF position and the

air compressor is unplugged.

 Confirm that the outlet pressure is at zero (0) psi by fully

turning the regulator knob counterclockwise to fully re-

duce air pressure at the outlet.

NOTE: Turning the knob clockwise increases air pressure

at the outlet. Turning counterclockwise reduces air pres-

sure at the outlet.

Attach coiled air hose to coupler on the side of the air

compressor.

 Connect the air compressor to a power supply and turn

power switch to the AUTO position.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 47 48

Commentaires sur ces manuels

Pas de commentaire

Ryobi YN301PL1 Manuel de l'opérateur Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Compresseurs d'air Ryobi YN301PL1