Ryobi YN301PL1 Manuel de l'opérateur télécharger pdf (Page 8)

8 - English

ELECTRICAL

EXTENSION CORDS

Use only 3-wire extension cords that have 3-prong grounding

plugs and 3-pole receptacles that accept the product’s plug.

When using a power tool at a considerable distance from the

power source, use an extension cord heavy enough to carry

the current that the tool will draw. An undersized extension

cord will cause a drop in line voltage, resulting in a loss of

power and causing the motor to overheat. Use the chart

provided below to determine the minimum wire size required

in an extension cord. Only round jacketed cords listed by

Underwriter’s Laboratories (UL) should be used.

**Ampere rating (on product data plate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0

Cord Length Wire Size (A.W.G.)

25' 16 16 16 16 14 14

50' 16 16 16 14 14 12

100' 16 16 14 12 10 —

**Used on 12 gauge - 20 amp circuit.

NOTE: AWG = American Wire Gauge

When working with the product outdoors, use an extension

cord that is designed for outside use. This is indicated by

the letters “W-A” or “W” on the cord’s jacket.

Before using an extension cord, inspect it for loose or

exposed wires and cut or worn insulation.

WARNING:

Keep the extension cord clear of the working area.

Position the cord so that it will not get caught on lumber,

tools, or other obstructions while you are working with a

power tool. Failure to do so can result in serious personal

injury.

WARNING:

Check extension cords before each use. If damaged

replace immediately. Never use the product with a

damaged cord since touching the damaged area could

cause electrical shock resulting in serious injury.

ELECTRICAL CONNECTION

This product is powered by a precision-built electric motor.

It should be connected to a power supply that is 120 V, AC

only, (normal household current) 60 Hz. Do not operate

this product on direct current (DC). A substantial voltage

drop will cause a loss of power and the motor will overheat.

If the product does not operate when plugged into an outlet,

double check the power supply.

GROUNDING INSTRUCTIONS

This product must be grounded. In the event of a malfunction

or breakdown, grounding provides a path of least resistance

for electric current to reduce the risk of electric shock.

This product is equipped with an electric cord having an

equipment-grounding conductor and a grounding plug. The

plug must be plugged into a matching outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

Do not modify the plug provided. If it will not fit the outlet,

have the proper outlet installed by a qualified electrician.

WARNING:

Improper installation of the grounding plug is liable

to result in a risk of electric shock. When repair or

replacement of the cord is required, do not connect the

grounding wire to either flat blade terminal. The wire with

insulation having an outer surface that is green with or

without yellow stripes is the grounding wire.

Check with a qualified electrician or service personnel if the

grounding instructions are not completely understood, or if

in doubt as to whether the product is properly grounded.

Repair or replace a damaged or worn cord immediately.

This product is for use on a nominal 120 V circuit and has

a grounding plug similar to the plug illustrated in figure 1.

Only connect the product to an outlet having the same

configuration as the plug. Do not use an adapter with this

product.

See Figure 1, page 16.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 47 48

Commentaires sur ces manuels

Pas de commentaire

Ryobi YN301PL1 Manuel de l'opérateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Compresseurs d'air Ryobi YN301PL1