Ryobi YG301PD Manuel d'utilisateur Page 11

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 44
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 10
11 - English
OPERATION
RESETTING THE COMPRESSOR
When amperage into the air compressor exceeds the specified
amperage, the air compressor will automatically shut off.
Turn the air compressor off.
Unplug the air compressor to allow unit to cool and to
trigger reset.
Plug the air compressor into an approved outlet.
Turn the air compressor on.
WARNING
Never exceed the air tool’s pressure rating as
recommended by the manufacturer. When using this
air compressor as an inflation device, always follow the
maximum inflation guidelines stated by the manufacturer
of the item being inflated.
WARNING
Always ensure the switch is in the OFF position and
the regulator pressure gauge reads zero (0) psi before
changing air tools or disconnecting the hose from the air
outlet. Failure to do so could result in possible serious
personal injury.
CONNECTING/DISCONNECTING HOSES TO
THE AIR COMPRESSOR
See Figure 6, pages 16.
When connecting/disconnecting a hose to the air compressor
always do the following:
Ensure AUTO/OFF switch is in the OFF position and the
air compressor is unplugged.
Confirm that the outlet pressure is at zero (0) psi by fully
turning the regulator knob counterclockwise to fully re-
duce air pressure at the outlet.
NOTE: Turning the knob clockwise increases air pressure
at the outlet. Turning counterclockwise reduces air pres-
sure at the outlet.
Attach coiled air hose to coupler on the side of the air
compressor.
Connect the air compressor to a power supply and turn
power switch to the AUTO position.
Allow unit to reach max pressure as indicated on the tank
pressure gauge.
Set regulator to desired pressure by rotating pressure
regulator knob. The regulator pressure will appear on the
gauge marked as outlet.
To disconnect a coiled air hose:
Confirm that the outlet pressure is at zero (0) psi.
When disconnecting a hose from 1/4-in. quick coupler,
always firmly hold release end of hose.
Pull back on the release sleeve on the 1/4-in. quick
coupler.
With a firm grip, pull out the quick-connect air fitting that
is attached to the quick coupler.
CONNECTING OR DISCONNECTING
PNEUMATIC TOOLS FROM THE AIR
COMPRESSOR
NOTE: When connecting a pneumatic air nailer or other air
tool always follow the manufacturer’s recommended start-
up procedure.
USING THE AIR COMPRESSOR
See Figure 5, page 16.
WARNING:
Risk of bursting. Do not adjust regulator to result in
output pressure greater than marked maximum pressure
of attachment and/or the item being inflated. Never use
at pressure greater than 135 psi. Failure to heed this
warning could result in possible serious personal injury.
WARNING:
Air powered tools may require more air consumption
than this air compressor is capable of providing. Check
the tool manual to avoid damage to the tool or risk of
personal injury.
Follow the instructions in “Connecting/Disconnecting
Hoses to the Air Compressor.”
Control the amount of air flow with the pressure regulator
knob. Turning the knob fully counterclockwise will
completely stop the flow of air, as shown in the start up
section of the quick reference label.
NOTE: Always use the minimum amount of pressure
necessary for your application. Using a higher pressure
than needed will drain air from the tank more rapidly and
cause the unit to cycle on more frequently.
When finished, always drain the tank and unplug the
unit. Never leave the unit plugged in and/or running
unattended.
Vue de la page 10
1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 43 44

Commentaires sur ces manuels

Pas de commentaire