Ryobi P241 Manuel de l'opérateur télécharger pdf (Page 9)

9 – English

OPERATION

TO INSTALL/REMOVE BATTERY PACK

See Figure 2, page 12.

WARNING:

Always remove battery pack from your tool when you are

assembling parts, making adjustments, cleaning, or when

not in use. Removing battery pack will prevent accidental

starting that could cause serious personal injury.

To install:

Place the battery pack in the tool. Align the raised rib on

the battery pack with groove in the battery port.

Make sure the latches on each side of the battery pack

snap in place and that the battery pack is secured in the

tool before beginning operation.

To remove:

Depress the latches on both sides of the battery pack to

release the battery pack and remove it from the tool.

WARNING:

Battery tools are always in operating condition. Therefore,

switch should always be locked when not in use or car-

rying at your side.

SWITCH TRIGGER

See Figure 3, page 12.

To turn the drill ON, depress the switch trigger. To turn it

OFF, release the switch trigger.

VARIABLE SPEED

This tool has a variable speed switch trigger that delivers

higher speed with increased trigger pressure. Speed is con-

trolled by the amount of switch trigger depression.

NOTE: You might hear a whistling or ringing noise from the

switch during use. Do not be concerned; this is a normal

part of the switch function.

DIRECTION OF ROTATION SELECTOR

(FORWARD/REVERSE/CENTER LOCK)

See Figure 3, page 12.

The direction of bit rotation is reversible and is controlled

by a selector located above the switch trigger. With the drill

held in normal operating position, the direction of rotation

selector should be positioned to the left of the switch trigger

for forward drilling. The drilling direction is reversed when

the selector is to the right of the switch trigger.

Setting the direction of rotation selector in the OFF (center

lock) position helps reduce the possibility of accidental start-

ing when not in use.

CAUTION:

To prevent gear damage, always allow chuck to come

to a complete stop before changing the direction of

rotation.

To stop the drill, release switch trigger and allow the chuck

to come to a complete stop.

NOTE: The drill will not run unless the direction of rotation

selector is pushed fully to the left or right.

Avoid running the drill at low speeds for extended periods

of time. Running at low speeds under constant usage may

cause the drill to become overheated. If this occurs, cool the

drill by running it without a load and at full speed.

KEYLESS CHUCK

See Figure 4, page 12.

The drill has a keyless chuck to tighten or release drill bits

in the chuck jaws. The arrows on the chuck indicate which

direction to rotate the chuck body in order to LOCK (tighten)

or UNLOCK (release) the drill bit.

Grasp and hold the collar of the chuck with one hand. Ro-

tate the chuck body with your other hand. This chuck has

a racheting design that allows the user to hear a series of

“clicks” while tightening the jaws. This “clicking” will stop

once the chuck and jaws are secure.

WARNING:

Do not hold the chuck body with one hand and use the

power of the drill to tighten the chuck jaws on the drill

bit. The chuck body could slip in your hand or your hand

could slip and come in contact with rotating drill bit. This

could cause an accident resulting in serious personal

injury.

INSTALLING/REMOVING BITS

See Figures 4 - 5, page 12.

To install:

Lock the switch trigger by placing the direction of rotation

selector in the center position.

Openorclosethechuckjawstoapointwheretheopen-

ing is slightly larger than the bit size you intend to use.

Also, raise the front of the drill slightly to keep the bit from

falling out of the chuck jaws.

Insert the drill bit.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 35 36

Commentaires sur ces manuels

Pas de commentaire

Ryobi P241 Manuel de l'opérateur Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Chargeurs de batterie Ryobi P241