Ryobi RP4300 Manuel de l'opérateur Page 8

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 28
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 7
8 — English
ARMING/DISARMING THE DEVICE
See Figure 4, page 10.
When arming the device, Alarm mode is the default selec-
tion.
To arm the device from the keypad:
Enter your personal security code.
Press the ARM button.
Once armed, you have approximately 30 seconds to
choose between chime or alarm mode and leave the
area.
To arm the device from the remote control:
Press the ARM button.
Once armed, you have approximately 30 seconds to leave
the area.
NOTE: You cannot choose between chime and alarm
using the remote control. To choose between chime and
alarm, you must use the motion alarm’s keypad.
To disarm the device from the keypad:
Enter your personal security code.
Press the DISARM button.
To disarm the device from the remote control:
Press the DISARM button.
CHIME/ALARM MODE OPERATION
When the device is in Chime mode:
Once armed, an audible tone sounds as soon as someone
enters the sensor’s line of sight. The alert will continue
every 2 seconds until the person leaves the area. Once
the sensor no longer detects motion, it will reset back
into the armed state.
When the device is in Alarm mode:
Once armed, the alarm sequence will begin after
2 seconds of the sensor detecting continuous motion.
This helps to avoid nuisance alarms such as animals
entering and leaving the area quickly.
After 2 seconds of continuous motion, the LED will blink
for 13 seconds to allow the operator time to disarm the
device before the alarm is triggered.
Once the alarm is triggered, it will sound for 2 minutes.
If motion is still detected after that time, the alarm will
continue to sound for another 2 minutes. If no motion
is detected, the alarm will reset back into the armed
state.
Enter the desired new security code. This code must be
between 4 and 10 digits and must be entered within 30
seconds.
Press the # key to store the new code in the device. The
LED will turn off if the new code is stored successfully.
NOTE: The device will also provide audible feedback when
changing the security code. If the device beeps twice at any
time, the previous step is accepted. If the device beeps four
times, the previous step was incorrect and the procedure
should be started over from the beginning.
POSITIONING THE MOTION ALARM
See Figures 4 - 5, page 10.
Positioning the motion alarm:
The motion alarm can be set on a flat surface, mounted
with standard drywall screws (not included), or attached
to the mounting bracket with screws supplied and se-
cured using rope or webbing.
The device has a detection range of 110 degrees up to
a distance of 30 feet. Follow the procedures in Testing
the detection range to make sure the area for which you
desire coverage is included in this range.
Testing the detection range:
The test mode allows you to judge the area that is being
protected and adjust the position of the device as needed
to make sure the desired areas are covered.
To enter test mode: Press and hold the CHIME/ALARM button
and then press the # button.
The device will take approximately 30 seconds to scan the
area, then the LED will blink and a brief tone will sound for
as long as the device detects motion. Walk around the area
where motion sensing is desired. Any time the LED turns
solid and the sound stops, you are out of the area where
the device can detect motion.
To exit the test mode: Press and hold the CHIME/ALARM
button and then press the # button.
NOTE: The test mode can only be initiated from the
keypad.
OPERATION
Vue de la page 7
1 2 3 4 5 6 7 8 9 10 11 12 13 ... 27 28

Commentaires sur ces manuels

Pas de commentaire