Ryobi TC401 Manuel d'utilisation et d'entretien télécharger pdf (Page 11)

11 — English

To stop the saw: Release the switch trigger.

After you release the switch trigger, allow the wheel to come

to a complete stop. DO NOT remove the saw from the

workpiece while the wheel is moving.

LOCK-ON BUTTON

See Figure 7, page 16.

The saw is equipped with a lock-on feature, which is conve-

nient for continuous use for extended periods of time.

To lock-on:

Depress the switch trigger.

Push in and hold the lock-on button, located on the side

of the handle.

Release the switch trigger.

Release the lock-on button.

To release the lock, depress and release the switch

trigger.

ADJUSTING CUTTING WHEEL DEPTH

See Figure 8, page 16.

Always keep correct wheel depth setting. The correct wheel

depth setting for all cuts should not exceed 1/4 in. below the

material being cut. More wheel depth will increase the chance

of kickback and cause the cut to be rough.

To adjust the wheel depth:

Unplug the saw.

WARNING:

Failure to unplug the tool could result in accidental start-

ing causing serious injury.

Loosen depth lock knob by turning it counter-clockwise.

Hold base flat against the workpiece and raise or lower

saw until the desired depth of cut is reached.

Tighten depth lock knob securely by turning it clockwise.

OPERATING THE SAW

See Figures 9 - 10, page 16.

It is important to understand the correct method for operat-

ing the saw. Refer to the figures in this section to learn the

correct and incorrect ways for handling the saw.

WARNING:

To make sawing easier and safer, always maintain proper

control of the saw. Loss of control could cause an ac-

cident resulting in possible serious injury.

WARNING:

When lifting the saw from the workpiece, the wheel is

exposed on the underside of the saw.

OPERATION

To make the best possible cut:

Hold the saw firmly.

Avoid placing your hand on the workpiece while making

a cut.

Support the workpiece so that the cut is always on your left.

Support the workpiece near the cut.

Clamp the workpiece securely so that the workpiece will

not move during the cut.

Avoid placing the saw on the part of the workpiece that

will fall off when the cut is made.

Place the workpiece with the “good” side down.

Draw a guideline along the desired line of cut before

beginning your cut.

Keep the cord away from the cutting area. Always place

the cord to prevent it from hanging up on the workpiece

while making a cut.

 If wet cutting is desired, turn the water supply valve to

start water flow.

DANGER:

If the cord hangs up on the workpiece during a cut,

release the switch trigger immediately and allow the

wheel to come to a complete stop. Unplug the saw and

reposition the cord to prevent it from hanging up again.

DANGER:

Using a saw with a damaged cord could result in serious

injury or death. If the cord has been damaged, have it

replaced before using the saw again.

MAKING CUTS

Always draw the line to be cut on the tile using a marker or

grease pencil. If the tile is shiny and hard-to-mark, place

masking tape on the tile and mark the tape.

A common problem when cutting tile is straying from the

marked line. Once you’ve strayed from the mark, you can not

force the wheel back to the line by twisting the tile. Instead,

back up and recut the tile slicing off a small amount of tile

until the wheel is back on track.

To avoid this problem, use a straight edge guide whenever

possible for making cross cuts and miter cuts.

If wet cutting is desired, it should be performed outside.

TO MAKE A CROSS CUT

See Figure 11, page 16.

Cross cuts are straight 90º cuts. The material is fed into the

cut at a 90º angle to the wheel, and the wheel is vertical.

 Using a marker or grease pencil, mark the area to be cut

on material.

 Secure the workpiece.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 43 44

Commentaires sur ces manuels

Pas de commentaire

Ryobi TC401 Manuel d'utilisation et d'entretien Page 11

Commentaires sur ces manuels