Ryobi TC401 Manuel d'utilisation et d'entretien télécharger pdf (Page 3)

3 — English

Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

SERVICE

Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

When servicing a power tool, use only identical

replacement parts. Follow instructions in the

Maintenance section of this manual. Use of unauthorized

parts or failure to follow Maintenance instructions may

create a risk of shock or injury.

SAFETY INSTRUCTIONS FOR

ABRASIVE CUTTING-OFF OPERATIONS

 The guard provided with the tool must be securely

attached to the power tool and positioned for

maximum safety, so the least amount of wheel is

exposed towards the operator. Position yourself and

bystanders away from the plane of the rotating wheel.

The guard helps to protect operator from broken wheel

fragments and accidental contact with wheel.

 Use only diamond cut-off wheels for your power tool.

Just because an accessory can be attached to your

power tool, it does not assure safe operation.

 The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed

can break and fly apart.

 Wheels must be used only for recommended

applications. For example: do not grind with the side

of cut-off wheel. Abrasive cut-off wheels are intended for

peripheral grinding, side forces applied to these wheels

may cause them to shatter.

 Always use undamaged wheel flanges that are of

correct diameter for your selected wheel. Proper wheel

flanges support the wheel thus reducing the possibility

of wheel breakage.

 The outside diameter and the thickness of your

accessory must be within the capacity rating of your

power tool. Incorrectly sized accessories cannot be

adequately guarded or controlled.

 The arbour size of wheels and flanges must properly fit

the spindle of the power tool. Wheels and flanges with

arbour holes that do not match the mounting hardware of

the power tool will run out of balance, vibrate excessively

and may cause loss of control.

 Do not use damaged wheels. Before each use, inspect

the wheels for chips and cracks. If power tool or

wheel is dropped, inspect for damage or install an

undamaged wheel. After inspecting and installing the

wheel, position yourself and bystanders away from

the plane of the rotating wheel and run the power tool

at maximum no load speed for one minute. Damaged

wheels will normally break apart during this test time.

 Wear personal protective equipment. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and shop apron capable

of stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping flying

debris generated by various operations. The dust mask or

respirator must be capable of filtrating particles generated

by your operation. Prolonged exposure to high intensity

noise may cause hearing loss.

 Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal

protective equipment. Fragments of workpiece or of

a broken wheel may fly away and cause injury beyond

immediate area of operation.

 Hold the power tool by insulated gripping surfaces

only, when performing an operation where the cutting

accessory may contact hidden wiring or its own cord.

Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and could

give the operator an electric shock.

 Position the cord clear of the spinning accessory. If

you lose control, the cord may be cut or snagged and

your hand or arm may be pulled into the spinning wheel.

 Never lay the power tool down until the accessory has

come to a complete stop. The spinning wheel may grab

the surface and pull the power tool out of your control.

 Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into your

body.

GENERAL POWER TOOL SAFETY WARNINGS

1 2 3 4 5 6 7 8 ... 43 44

Commentaires sur ces manuels

Pas de commentaire

Ryobi TC401 Manuel d'utilisation et d'entretien Page 3

Commentaires sur ces manuels