SAVE THIS MANUAL FOR FUTURE REFERENCEYour miter saw has been engineered and manufactured to our high standard for dependability, ease of operation, an
10FEATURESFig. 3KNOW YOUR COMPOUND MITER SAWSee Figure 1.The safe use of this product requires an understanding of the information on the tool and in
11FEATURESSPINDLE LOCK BUTTONSee Figure 3.The spindle lock button locks the spindle stopping the blade from rotating. Depress and hold the lock butto
12LOOSE PARTS LISTFig. 6WARNING:The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.The follow
13ASSEMBLYWARNING:Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible seriou
14ASSEMBLYWARNING:Always make sure the compound miter saw is securely mounted to a workbench or an approved workstand. Fail-ure to heed this warning c
15ASSEMBLY Using the wrench provided, loosen and remove the blade bolt. NOTE: The blade bolt has left hand threads. Turn blade bolt clockwise to lo
16ASSEMBLYWORK CLAMPSee Figure 12.The work clamp provides greater control by clamping the workpiece to the fence or the table. It also prevents the wo
17ASSEMBLYDANGER:Laser radiation. Avoid direct eye contact with light source.WARNING:Use of controls or adjustments or performance of pro-cedures othe
18ASSEMBLYNOTE: Many of the illustrations in this manual show only portions of the compound miter saw. This is intentional so that we can clearly sho
MITER TABLESQUAREBEVEL LOCK KNOBMITER FENCEBLADE19ASSEMBLYSCALE INDICATORMITER SCALEINDICATOR SCREWBEVEL SCALESQUARING THE BLADE TO THE MITER TABLESee
2 Introduction ...
20OPERATIONWARNING:Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict se
21OPERATION NOTE: You can quickly locate 0°, 15°, 22-1/2°, 31.62° and 45° left or right as you rotate the control arm. The miter table will seat itse
22OPERATION Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side agai
230OPERATION Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side aga
24OPERATION4 PITCH OF SIDENUMBER OF SIDES0°6M- 45.00°B- 0.00°5°10°15°20°25°30°35°40°45°50°55°60°65°70°75°80°85°90°578 910M- 36.00°B- 0.00°M- 3
25OPERATIONWhen setting the bevel and miter angles for compound miters, remember that the settings are interdependent; changing one angle changes the
26OPERATIONWARNING: To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material against the
27ADJUSTMENTSWARNING:Before performing any adjustment, make sure the tool is unplugged from the power supply. Failure to heed this warning could resul
28ADJUSTMENTSDANGER:Laser radiation. Avoid direct eye contact with light source.WARNING:Use of controls or adjustments or performance of pro-cedures o
29ADJUSTMENTSTO ADJUST THE MITER LOCK LEVERSee Figure 37.Prior to squaring the saw blade to the fence, check and adjust the miter lock lever, if neede
3GENERAL SAFETY RULESWARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fir
30MAINTENANCEWARNING:When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.WARNING:
NOTES / NOTAS
99000027812-3-12 (REV:03)OPERATOR’S MANUAL7-1/4 in. Compound Miter SawTS1142L - Double Insulated• SERVICENow that you have purchased your tool, shoul
4GENERAL SAFETY RULES NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes. INSPECT TOOL CORDS PERIODICALLY. If
5SPECIFIC SAFETY RULES NEVER hand hold a workpiece that is too small to be clamped. Keep hands clear of the cutting area. NEVER reach behind, unde
6SYMBOLSThe following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANINGDANGER
7ELECTRICALDOUBLE INSULATIONDouble insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire groun
8GLOSSARY OF TERMSPush Blocks (jointer planers)Device used to feed the workpiece over the jointer planer cutterhead during any operation. This aid hel
9FEATURESFig. 1PRODUCT SPECIFICATIONSArbor .................. 5/8 in.Blade Diameter ....
Commentaires sur ces manuels