Ryobi SSP100 Manuel d'utilisateur télécharger pdf (Page 7)

English

FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR

OPERATION

NOTE: The tip should be tightened securely by

hand. A too loose or overtightened tip may cause the

sprayer to leak or be damaged.

To change direction of fan tip from Horizontal to

Vertical:

Q Slightly loosen the fan tip by rotating counterclockwise

1/4 turn.

Q Rotate the adjusting arm 1/4 turn in the direction

needed to switch the direction of the tip spray.

Q While holding the adjusting arm in position, rotate the

fan tip clockwise until securely tightened.

WARNING

To reduce the risk of injection, do not point

sprayer at any part of the body or person. In

case of skin injection, seek medical attention

immediately. Do not use without spray tip in

place.

OPERATING THE SPRAYER

See Figure 6-9.

Q Place a line of lubricant on the piston. To gain access

to the piston, follow the instructions in Cleaning the

Sprayer for Storage in the Maintenance section of

this manual.

Q Ensure surface to be painted is free of dust, dirt, and

grease.

Q Mask or cover any areas not intended to be painted

or stained. Be aware of wind that may cause your

paint or stain to spray into areas not desired. Always

use drop cloths or other cover to protect areas that

are not intended to be painted or stained.

Q Fill the quick-lock container with no more than 1 liter

of desired paint or stain.

NOTE: After every 4 refills of the quick-lock

container, add a line of lubricant to the piston. See

Cleaning the Sprayer for Storage for instructions

on disassembling the sprayer to gain access to the

piston.

Q Select the proper spray tip for desired spray pattern.

Q Plug in the sprayer.

Q Pull the switch trigger to spray paint. Release the

switch trigger to stop paint spray.

Q Practice spraying on a piece of scrap material to test

your spray pattern and to prime the pump before

beginning. If you cannot get a good spray pattern with

an even amount of paint or stain throughout, refer to

either the Dilution section or Troubleshooting section

later in this manual.

NOTE: The pump must be primed after every paint

change and at first use after storing. Spray paint at a

scrap surface for at least 20 seconds to prime.

Q To create an even coating over the entire surface:

• Move your arm at a steady rate of speed and make

sure to move your entire arm, not just your wrist.

• Keep the sprayer an even distance from the area

being sprayed, which should be between 20 to 25

cm from the tip of the sprayer to the surface being

sprayed.

• Depress the trigger to begin the spray off the material

you want to paint. Operate the sprayer in straight

horizontal or vertical strokes across the surface

being painted, then release the trigger off the

material to end the stroke.

NOTE: For spray quality consistency when using

thinner paints, it may be necessary to keep the

trigger depressed between strokes.

Q When finished, unplug the sprayer, return any unused

paint or stain to its original container, and thoroughly

clean the sprayer.

CAUTION

It is important to thoroughly clean the sprayer

after each use or when changing colors. Allowing

paint or stain to remain in an idle tool for an

extended period can cause its moving pieces to

seize up.

CLEANING THE SPRAYER AFTER USE

The solution used to clean the sprayer is determined by

the type of material that has been sprayed. For anything

other than water based material, follow the material

manufacturer’s directions for appropriate clean-up.

To clean the sprayer for short term storage:

Q Unplug the sprayer.

Q If you haven’t already done so, remove the paint

container and return any unused paint or stain to its

original container.

Q Fill the paint container with lukewarm water (following

the use of water based products) or Cleaning

Solvent/Paint Thinner (following the use of oil-based

products).

Q Reinstall the paint container.

Q Plug in the sprayer.

Q Spray the solution onto a piece of cardboard or other

scrap material. Continue spraying until all the solution

is used.

Q Unplug the sprayer.

1 2 3 4 5 6 7 8 9 10 11 12 ... 155 156

Commentaires sur ces manuels

Pas de commentaire

Ryobi SSP100 Manuel d'utilisateur Page 7

Commentaires sur ces manuels