Ryobi RY52014 Manuel de l'opérateur

Naviguer en ligne ou télécharger Manuel de l'opérateur pour Outils de jardin Ryobi RY52014. Ryobi RY52014 Operator`s manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 22
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté4.6 / 5. Basé sur9 avis des utilisateurs
Vue de la page 0
OPERATOR’S MANUAL
TP30 GAS PRUNER
RY52014
SAVE THIS MANUAL FOR FUTURE REFERENCE
Your pruner has been engineered and manufactured to our high standard for dependability, ease of operation, and operator
safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
Vue de la page 0
1 2 3 4 5 6 ... 21 22

Résumé du contenu

Page 1 - OPERATOR’S MANUAL

OPERATOR’S MANUALTP30 GAS PRUNERRY52014SAVE THIS MANUAL FOR FUTURE REFERENCEYour pruner has been engineered and manufactured to our high standard for

Page 2 - INTRODUCTION

10WARNING: Do not allow familiarity with tools to make you care-less. Remember that a careless fraction of a second is sufficient to inflict

Page 3 - GENERAL SAFETY RULES

11OPERATIONFig. 7CUTTING GUIDEFig. 6�NOTE: For second and final cuts (from top of limb or branch), hold front cutting guide against the limb being cu

Page 4 - SPECIFIC SAFETY RULES

12OPERATIONFig. 12POSITION FOR STARTINGSee Figure 9.Lay the pruner on the ground and ensure that no objects or obstructions are in the immediate vicin

Page 5 - 50' 15m

13FLATSAPPROX .050 IN. (1.25 mm)Fig. 14Fig. 13WARNING:When servicing, use only identical replacement parts. Use of any other parts may create

Page 6 - SAVE THESE INSTRUCTIONS

14MAINTENANCEREPLACING THE BARSee Figures 15 - 20.WARNING: To avoid possible serious injury, stop engine before re-placing the bar, chain, or performi

Page 7 - FEATURES

15IDLE SPEED ADJUSTMENTSee Figure 21.If the chain turns at idle, the idle speed screw needs adjusting on the engine. Turn the idle speed screw counter

Page 8 - ASSEMBLY

16MAINTENANCECUTTING CORNERSIDE PLATEDEPTH GAUGETOEGULLETHEELRIVET HOLETOP PLATEPARTS OF A CUTTERFig. 24HOW TO SHARPEN THE CUTTERSSee Figures 24 - 27.

Page 9

17MAINTENANCEFig. 28Fig. 29AIR FILTERCOVERLATCHREPLACING AND CLEANING AIR FILTERSee Figure 28.For proper performance and long life, keep air filter cl

Page 10 - OPERATION

18TROUBLESHOOTINGPROBLEM CAUSE REMEDYEngine will not start. No spark. No fuel. Engine is flooded. Starter rope pulls harder now than when new.C

Page 11

19WARRANTYLIMITED WARRANTY STATEMENTTechtronic Industries North America, Inc., warrants to the original retail purchaser that this RYOBI® brand outdoo

Page 12

2 Introduction ...

Page 13 - MAINTENANCE

20WARRANTYTHE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES TO MODEL NUMBERS REQUIRED TO MEET THE CARB REQUIREMENTS.TECHTRONI

Page 14

21WARRANTYEMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LISTEmissions Parts Inspect Before Clean Every Replace Clean Every Replace Every

Page 15

983000-88211-29-05 (REV:00)OPERATOR’S MANUALTP30 GAS PRUNERRY52014 WARNING:The engine exhaust from this product contains chemicals known to the State

Page 16

3WARNING!Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious pers

Page 17

4 Kickback is a dangerous reaction that can lead to serious injury. Kickback may occur when the moving chain con-tacts an object at the upper portion

Page 18 - TROUBLESHOOTING

5SYMBOLSGasoline and OilUse unleaded gasoline intended for motor vehicle use with an octane rating of 87 [(R + M)/2] or higher. This product is powere

Page 19 - WARRANTY

6SYMBOLSSERVICEServicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we su

Page 20

7 FEATURESFig. 1PRODUCT SPECIFICATIONSEngine Displacement ...

Page 21 - 1-800-860-4050

8ATTACHING THE “J” BARRIER HANDLESee Figure 2. Hold the top and bottom clamp snugly in position on the shaft housing so that the handle will be loca

Page 22

9 Reinstall the bolt, lock washer, and hex nut to secure. Connect the latch on the shoulder harness to the strap hanger.ASSEMBLYCONNECTING THE POW

Commentaires sur ces manuels

Pas de commentaire