Ryobi RYI2200G Manuel d'utilisateur télécharger pdf (Page 19)

15 — English

MAINTENANCE

 Tilt the generator to the side and allow lubricant to drain

from the oil fill hole into an approved container.

NOTE: Drain the lubricant while the engine is still warm

but not hot. Warm lubricant will drain quickly and more

completely.

WARNING:

Do not change engine lubricant while it is hot. Accidental

contact with hot engine lubricant could result in serious

burns.

 Return the generator to an upright position and refill with

lubricant following the instructions in the Checking/

Adding Lubricant section previously in this manual.

For amount of lubricant needed to refill, see Product

Specifications earlier in this manual or the accompanying

engine manual, if applicable.

 Replace and secure the oil cap/dipstick.

 Reinstall the engine cover. Replace the screw and tighten

securely.

NOTE: Used lubricant should be disposed of at an approved

disposal site. See your local retailer for more information.

SPARK PLUG REPLACEMENT

See Figure 13.

The spark plug must be properly gapped and free of deposits

in order to ensure proper engine operation. To check:

 Remove the spark plug cover.

 Remove the spark plug cap.

 Clean any dirt from around base of spark plug.

 Remove spark plug using spark plug wrench.

 Inspect spark plug for damage, and clean with a wire

brush before reinstalling. If insulator is cracked or

chipped, spark plug should be replaced. For replacement

spark plug, see Product Specifications earlier in this

manual or the accompanying engine manual, if applicable.

 Measurepluggap.Thecorrectgapis0.024−0.028in.

(0.60-0.70 mm). To widen gap, if necessary, carefully

bend the ground (top) electrode. To lessen gap, gently

tap ground electrode on a hard surface.

 Seat spark plug in position; thread in by hand to prevent

cross-threading.

 Tighten with wrench to compress washer. If spark plug

is new, use 1/2 turn to compress washer appropriate

amount. If reusing old spark plug, use 1/8 to 1/4 turn for

proper washer compression.

NOTE: An improperly tightened spark plug will become

very hot and could damage the engine.

NOTICE:

Be careful not to cross-thread the spark plug. Cross-

threading will seriously damage the product.

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts could create a hazard or cause

product damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes, resulting in possible

serious injury.

GENERAL MAINTENANCE

Keep the generator in a clean and dry environment where it

is not exposed to dust, dirt, moisture, or corrosive vapors.

Do not allow the cooling air slots in the generator to become

clogged with foreign material such as leaves, etc.

Do not use a garden hose to clean the generator. Water

entering the fuel system or other internal parts of the unit can

cause problems that will decrease the life of the generator.

To clean the unit:

 Use a soft bristle brush and/or vacuum cleaner to loosen

and remove dirt and debris.

 Clean air vents with low pressure air that does not exceed

25 psi.

 Wipe the exterior surfaces of the generator with a damp cloth.

CHECKING/CLEANING AIR FILTER

See Figures 10 - 11.

For proper performance and long life, keep air filter clean.

 Loosen the screws on the side of the engine cover.

Remove cover and set aside.

 Loosen the screw in the center of the air filter cover and

turn the cover 1/4 turn clockwise, pulling the cover down

and off the unit. Remove air filter cover and set aside.

 Remove both the large and the small air filters.

 Wash the air filters with warm, soapy water. Rinse and

squeeze to dry.

 Reinstall the air filters.

NOTE: Make sure the filters are seated properly inside

the generator. Installing the filters incorrectly will allow

dirt to enter the engine, causing rapid engine wear.

 Reinstall the air filter cover. Tighten screw to secure.

 Reinstall the engine cover. Tighten screws to secure.

CHANGING ENGINE LUBRICANT

See Figure 12.

For best performance, engine lubricant should be changed

after every 100 hours or 6 months of operation.

 Loosen the screw at the top of the engine cover. Remove

cover and set aside.

 Remove the oil fill cap/dipstick.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 63 64

Commentaires sur ces manuels

Pas de commentaire

Ryobi RYI2200G Manuel d'utilisateur Page 19

Commentaires sur ces manuels

Produits connexes et manuels pour Générateurs Ryobi RYI2200G