Ryobi RYI2200H Manuel d'utilisateur télécharger pdf (Page 18)

14 — English

OPERATION

STARTING THE ENGINE

See Figures 5 - 7.

NOTICE:

On a level surface with the engine off, check the lubricant

level before each use of the generator.

NOTE: If location of generator is not level, the unit may not

start or may shut down during operation.

To start generator the first time:

Your new inverter generator is equipped with a mechanical

fuel pump. The initial start up will require additional pulls of

the recoil starter to prime the fuel system.

 Turn the ENGINE/CHOKE LEVER to the CHOKE position.

 Fill the fuel tank per the Operator’s Manual instructions.

 Pull the engine recoil five (5) times to prime the fuel system.

 Press the AUTO IDLE SWITCH to the OFF position.

 Add engine lubricant per the Operator’s Manual

instructions.

 Pull the recoil starter until the engine starts.

 Move the CHOKE LEVER to the RUN position.

 For quieter more efficient operation, place the AUTO IDLE

switch in the ON position.

To start subsequent times:

NOTE: Subsequent starting should only require 6 pulls

maximum.

 Unplug all loads from the generator.

 Place the auto idle switch in the off position.

 Slide the engine/choke lever to the start (center) position.

NOTE: When the engine/choke lever is in the start (center)

position, the fuel will flow from the fuel tank to the engine.

If engine is warm, move the engine/choke lever right to

the run (restart) position.

 Pull the recoil starter until the engine runs (a maximum

of 6 times).

NOTE: Do not allow the grip to snap back after starting;

return it gently to its original place. Initial starting of the

unit may require additional pulls to prime the fuel pump.

 Allow the engine to run for 15-30 seconds, then move

the engine/choke lever right to the run position.

STOPPING THE ENGINE

See Figures 5 - 6.

 Remove any load from the generator.

 Place the engine/choke lever in the off position.

To stop the engine in an emergency situation:

 Put the engine/choke lever in the off position.

WARNING:

While operating and storing, keep at least 3 feet of clear-

ance on all sides of this product, including overhead.

Allow a minimum of 30 minutes of “cool down” time

before storage. Heat created by muffler and exhaust

gases could be hot enough to cause serious burns and/

or ignite combustible objects.

USING THE BATTERY CHARGING CABLE

See Figure 8.

WARNING:

The 12 V DC receptacle is designed to charge vented wet

lead acid batteries only. Other types of batteries could

burst, causing personal injury and damage.

NOTICE:

The 12 V DC receptacle provides continuous charge. Do

not overcharge battery or leave battery unattended. Doing

so may cause damage to the battery.

NOTICE:

Do not use the generator to jump start vehicles. Doing

so could result in damage to the vehicle or it’s electrical

components.

 Place the auto idle switch in the OFF position.

 Using the battery clamps, connect the battery charging

cable assembly to the battery terminal. Connect the

red wire to the positive (+) terminal first, then connect

the black wire to the negative (–) terminal. Make sure all

connections are secure.

NOTE: Be careful not to short across the terminals when

installing. Shorting the terminals together can cause

sparks, damage to the battery or generator, or even burns

or explosions.

NOTE: To prevent short circuit, keep away from a metal

surface during clamp connection.

 Connect the battery charging cable assembly to the

12 V DC receptacle.

 Start the generator.

NOTE: The AC receptacles can be used while the DC

receptacle is in use.

 The battery will become slightly warm to the touch while

charging. This is normal and does not indicate a problem.

NOTE: Only use battery charging cable assembly to

charge vented wet lead acid batteries.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 71 72

Commentaires sur ces manuels

Pas de commentaire

Ryobi RYI2200H Manuel d'utilisateur Page 18

Commentaires sur ces manuels

Produits connexes et manuels pour Générateurs Ryobi RYI2200H