Ryobi RY6201 Manuel de l'opérateur

Naviguer en ligne ou télécharger Manuel de l'opérateur pour Fournitures d'outils à main Ryobi RY6201. Ryobi RY6201 Operator`s manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 20
  • Table des matières
  • MARQUE LIVRES
  • Noté4.9 / 5. Basé sur28 avis des utilisateurs
Vue de la page 0
THANK YOU FOR BUYING A RYOBI CORDLESS CIRCULAR SAW.
Your new cordless circular saw has been engineered and manufactured to Ryobi’s high standard for dependability, ease of
operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
CAUTION: Carefully read through this entire operator’s manual before using your new cordless circular saw.
Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your cordless circular saw properly
and only for what it is intended, you will enjoy years of safe, reliable service.
Thank you again for buying Ryobi tools.
OPERATOR'S MANUAL
5-1/2 in. (140 mm) CORDLESS
CIRCULAR SAW MODEL NO. RY6201
SAVE THIS MANUAL FOR FUTURE REFERENCE
SPECIFICATIONS:
Blade Diameter 5-1/2 in. (140 mm)
Blade Arbor 3/8 in. (10 mm)
Cutting Depth at 0° 1-9/16 in. (40 mm)
Cutting Depth at 45° 1-1/8 in. (29 mm)
No Load Speed 3,800 RPM
Motor 14.4 Volt DC
Charge Rate 1 Hour
Charger Rating 120 Volts, 60 Hz, AC
Vue de la page 0
1 2 3 4 5 6 ... 19 20

Résumé du contenu

Page 1 - 5-1/2 in. (140 mm) CORDLESS

THANK YOU FOR BUYING A RYOBI CORDLESS CIRCULAR SAW.Your new cordless circular saw has been engineered and manufactured to Ryobi’s high standard for de

Page 2

Page 1045455050303022221123045Fig. 6BLADESCREWBLADEWRENCHSPINDLELOCK BUTTON Fit saw blade inside lower blade guard and onto spindle.NOTE: The saw tee

Page 3 - RULES FOR SAFE OPERATION

Page 11KICKBACKSee Figure 8.The best guard against kickback is to avoid dangerouspractices.Kickback occurs when the blade stalls rapidly and the saw i

Page 4

Page 12 When making a cut use steady, even pressure. Neverforce cuts. Do not cut warped or wet lumber. Always hold your saw firmly with both hands

Page 5

Page 13TO HELP MAINTAIN CONTROL: Always support your workpiece near the cut. Support your workpiece so the cut will be on your left. Clamp your wor

Page 6 - SAVE THESE INSTRUCTIONS

Page 14TO CROSS CUT OR RIP CUTWhen making a cross cut or rip cut, align your line of cutwith the outer blade guide notch on the saw base asshown in fi

Page 7 - FEATURES

Page 15TO BEVEL CUTThe angle of cut of your saw may be adjusted to any desiredsetting between zero and 50°. NOTE: When making cuts at50°, blade should

Page 8

Page 1612450015223045504545505030302222POSITIVE 0° BEVEL STOPSee Figure 21.Your saw has a positive 0° bevel stop, that has been factoryadjusted to ass

Page 9 - TO ASSEMBLE OR REMOVE BLADE

Page 174545505030302222TO RIP CUTOPTIONAL RIP GUIDE (EDGE GUIDE)See Figure 23.Use a guide when making long or wide rip cuts with your saw.An optional

Page 10 - BLADE GUARD SYSTEM

Page 18WARNING:When servicing, use only identical replacement parts.Use of any other part may create a hazard or causeproduct damage.WARNING:Do not at

Page 12 - STARTING A CUT

Page 2Look for this symbol to point out important safety precautions. It means attention!!!Your safety is involved.The following recommended accessori

Page 13 - OPERATION

983000-060 4-02• SERVICENow that you have purchased your tool, should a need ever exist for repair parts or service,simply contact your nearest Ry

Page 14

Page 3WARNING:Do not attempt to operate this tool until you have readthoroughly and understand completely all instructions,safety rules, etc. containe

Page 15

Page 4IMPORTANT SAFETY RULES FOR BATTERYTOOLS Battery tools do not have to be plugged into an electricaloutlet; therefore, they are always in an oper

Page 16 - See Figure 22

Page 5RULES FOR SAFE OPERATION (Continued)IMPORTANT SAFETY INSTRUCTIONS FORCIRCULAR SAWS KEEP GUARDS IN PLACE AND IN WORKINGORDER. Never wedge or tie

Page 17

Page 6 SYMBOL NAME DESIGNATION/EXPLANATIONV Volts VoltageA Amperes CurrentHz Hertz Frequency (cycles per second)min Minutes TimeAlternating Current

Page 18 - MAINTENANCE

Page 7KNOW YOUR CORDLESS CIRCULAR SAWSee Figure 1.Before attempting to use any tool, familiarize yourself withall operating features and safety requir

Page 19

Page 8

Page 20

Page 945455050303022221123045WARNING:Always remove battery pack from your saw when youare assembling parts, making adjustments, assemblingor removing

Commentaires sur ces manuels

Pas de commentaire