Ryobi RY6201 Manuel de l'opérateur télécharger pdf (Page 5)

Page 5

RULES FOR SAFE OPERATION (Continued)

IMPORTANT SAFETY INSTRUCTIONS FOR

CIRCULAR SAWS

■ KEEP GUARDS IN PLACE AND IN WORKING

ORDER. Never wedge or tie lower blade guard open.

Check operation of lower blade guard before each use.

Do not use if lower blade guard does not close briskly

over saw blade.

■ If saw is dropped, lower blade guard or bumper may be

bent, restricting full return. If lower blade guard or

bumper becomes bent or damaged, replace them before

reuse.

■ KEEP BLADES CLEAN AND SHARP. Sharp blades

minimize stalling and kickback.

DANGER:

KEEP HANDS AWAY FROM CUTTING AREA. Keep

hands away from blade. Do not reach underneath work

while blade is rotating. Do not attempt to remove cut

material when blade is moving.

■ Blades coast after turn off.

■ USE RIP FENCE. Always use a fence or straight edge

guide when ripping.

■ SUPPORT LARGE PANELS. To minimize the risk of

blade pinching and kickback, always support large

panels as shown in Figure 11, Page 11. When cutting

operation requires the resting of the saw on the

workpiece, the saw should be rested on the larger

portion and the smaller piece cut off.

■ LOWER BLADE GUARD.

■ Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

■ If lower blade guard must be raised to make a cut,

always raise it with the retracting handle to avoid

serious injury.

See Figure 20, Page 15.

■ GUARD AGAINST KICKBACK.

Kickback occurs when the saw stalls rapidly and is

driven back towards the operator.

Release switch immediately if blade binds or saw stalls.

Keep blades sharp.

Support large panels as shown in Figure 11, Page 12.

Use fence or straight edge guide when ripping.

Don't force tool.

Stay alert – exercise caution.

Don't remove saw from work during a cut while the

blade is moving.

See Pages 12 and 13.

■ BEFORE MAKING A CUT, BE SURE THE DEPTH

AND BEVEL ADJUSTMENTS ARE TIGHT.

■ USE ONLY CORRECT BLADES. Do not use blades

with incorrect size holes. Never use blade washers or

bolts that are defective or incorrect. The maximum blade

capacity of your saw is 5-1/2 inches (140 mm).

■ NEVER touch the blade or other moving parts during

use.

■ NEVER start a saw when its blade is touching the

workpiece.

■ NEVER lay a tool down before its moving parts have

come to a complete stop.

■ SAVE THESE INSTRUCTIONS. Refer to them

frequently and use them to instruct others who may use

this tool. If you loan someone this tool, loan them these

instructions also.

WARNING:

Some dust created by power sanding, sawing, grinding,

drilling, and other construction activities contains

chemicals known to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to filter

out microscopic particles.

The operation of any power tool can result in foreign objects being thrown into your

eyes, which can result in severe eye damage. Before beginning power tool operation,

always wear safety goggles or safety glasses with side shields and a full face shield

when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or

standard safety glasses with side shields. Always use eye protection which is marked

to comply with ANSI Z871.1.

WARNING:

1 2 3 4 5 6 7 8 9 10 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Ryobi RY6201 Manuel de l'opérateur Page 5

Commentaires sur ces manuels