Ryobi RP4000 Manuel d'utilisateur télécharger pdf (Page 2)

OPERATION

OPERATIONOPERATION

WARNING:

Do not allow familiarity with products to make you careless.

Remember that a careless fraction of a second is sufficient

to inflict serious injury.

WARNING:

Always remove battery pack from the product when you are

assembling parts, making adjustments, cleaning, or when

not in use.

INSTALLING/REMOVING BATTERY PACK

See Figure 2.

 Pull and hold the height adjustment lever open to release the

inner console. Carefully remove the console from its jacket.

NOTE: Always hold the unit upright to remove the inner

console. Opening the height adjustment lever while turning

the plumb/cross laser upside down could cause the inner

console to fall out.

 Pull the tab on the battery cover to open the battery compart-

ment.

 Insert the battery pack into the unit. Make sure the raised rib

on the battery pack aligns with the groove in the compart-

ment. Press down on the battery pack to be sure contacts

on the battery pack engage properly with contacts in the

compartment.

 Close the battery cover and press the tab until it snaps into

place. Make sure it is securely fastened before operating the

plumb/cross laser.

 NOTE: Do not attempt to operate the plumb/cross laser if

the battery compartment is not closed or is missing.

 Holding the adjustment lever open, replace the inner console

into the jacket. Release the lever.

 When transporting the plumb/cross laser, keep the inner

console fully seated in the outer jacket (locked position).

TURNING THE LASER ON/OFF AND

SELECTING MODES

See Figure 3.

The ON/OFF/LASER MODE selector button is located on top

of the unit.

 To turn the laser on, press the ON/OFF/MODE selector button

on top of the unit. The laser will be in crosshair mode with

plumb dots above and below the unit.

 Press the button to change from crosshair to horizontal, and

again to change to vertical laser beam mode.

 To turn the laser off, press the button again.

MAINTENANCE

WARNING:

To avoid serious personal injury, always remove the battery

pack from the product when cleaning or performing any

maintenance.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-based

products, penetrating oils, etc., come in contact with plastic

parts. Chemicals can damage, weaken or destroy plastic

which may result in serious personal injury.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most plastics

are susceptible to damage from various types of commercial

solvents and may be damaged by their use. Use clean cloths

to remove dirt, dust, oil, grease, etc.

CAUTION:

Use of controls or adjustments or perfor mance of pro-

cedures other than those specified herein may result in

hazardous radiation exposure.

BATTERIES

This product will accept Ryobi 4 V lithium-ion batteries. Length

of service from each charging will depend on the type of work

you are doing.

Lithium-ion batteries have been designed to provide maximum

trouble-free life. However, like all batteries, they will eventually

wear out. Do not disassemble battery pack and attempt to replace

the batteries. Handling of these batteries, especially when wearing

rings and jewelry, could result in a serious burn.

A - Battery pack (bloc-pile, paquete de baterías)

B - Battery cover (compartiment des piles, tapa de las baterías)

C - Tab (ergots, orejetas)

D - Inner console (console interne, consola interior)

Fig. 1

REMOVE INNER CONSOLE FROM OUTER JACKET TO INSTALL

BATTERY PACK

(RETIRER LA CONSOLE INTERNE DE L’ENVELOPPE EXTÉRIEURE

AFIN D’INSTALLER LE BLOC-PILES,

RETIRE LA CONSOLA INTERIOR DE LA CUBIERTA EXTERIOR PARA

INSTALAR EL PAQUETE DE BATERÍAS)

Fig. 2

CORRECT OPERATING POSITION

See Figure 3.

 Set the plumb/cross laser on a stable surface or attach it to a

tripod (not included). There is a threaded tripod mount on the

bottom of the unit.

 For greatest accuracy, place the plumb/cross laser at a height

that allows the laser beam to be projected straight onto the

target surface.

 A lock icon in the side window indicates that the unit is locked

into place. When any part of the black lock icon is visible, the

unit is in locked position.

NOTE: Using the unit when the plumb/cross laser is locked

into the housing will not result in an accurate reading.

 Pull the inner console out of the jacket until the black lock icon

completely disappears from the window.

 Turn on the laser and select the laser beam mode you wish to

use.

 Allow the pendulum to self-level before marking level lines on

a target surface.

PLUMB/CROSS LASER MODES

See Figure 4.

Crosshair beam mode

The crosshair laser beam projects both a vertical and horizontal

line with plumb dots above and below the unit.

Horizontal beam mode

In horizontal beam mode, the beam is oriented for leveling items

horizontally, with a plumb dot directly above.

Vertical beam mode

In vertical beam mode, the laser beam is oriented for leveling

items vertically, with a plumb dot below the unit.

Plumb bob mode

In crosshair beam mode, the plumb/cross laser generates a

vertical upper and lower plumb dot. It can be used as a laser

plumb bob.

OUT-OF-LEVEL INDICATOR

The plumb/cross laser is designed for accuracy when the unit

itself is not tilted more than 5°. If the unit is tilted more than

5°, the laser will automatically shut off, to prevent inaccurate

readings.

A white backlight appears in the top laser aperture area to indicate

that the auto-leveling feature is enabled. If the unit is out of level,

the white light will blink continuously until this is corrected.

FINE HEIGHT ADJUSTMENT

To select the height of the beam, pull the adjustment lever and

slide the unit up or down in its jacket.

For fine-tuning the height of the beam, turn the height adjust-

ment screw in the direction indicated.

LOW BATTERY INDICATOR

The low battery indicator on top of the unit will flash when the

battery needs to be recharged.

A - On/off/laser mode selector button (Bouton sélecteur

de mode « On/off/laser » (Marche/Arrêt/Laser),

botón selector de encendido/apagado/modo de

láser)

B - Laser height adjustment screw (Vis de réglage de

la hauteur du laser, tornillo de ajuste de altura de

láser)

C - Height adjustment lever(Levier de réglage de la

hauteur , palanca de ajuste de altura)

D - Laser aperture (upper) (Ouverture (supérieure) du

laser), abertura del láser [superior])

E - Laser aperture (lower) (Ouverture (inférieure) du

laser), abertura del láser [inferior])

F - Laser aperture (front) (Ouverture (avant) du laser),

abertura del láser [delantera])

G - Lock icon (Icône de verrouillage, ícono de candad)

H - Leveling pendulum (Pendule de nivellement,

péndulo de nivelación)

I - Out-of-level indicator light (Lumière de

l’indicateur d’erreur de nivellement,

luz indicadora de fuera de nivelación)

J - Low battery indicator (Indicateur de

faible niveau des piles, indicador

de batería baja)

1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire

Ryobi RP4000 Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Écouteurs Ryobi RP4000