Ryobi RLM4619SME Manuel de l'opérateur Page 7

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 15
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 6
English
5
SETTING BLADE HEIGHT
See figure 6.
When shipped, the wheels on the mower are set to a low-
cutting position. Before using the mower for the rst time,
adjust the cutting position to the height best suited for your
lawn. The average lawn should be between 3 and 6 cm,
depending on the season.
To raise the blade height, grasp the height adjustment
lever and move it toward the back of the mower.
To lower the blade height, grasp the height adjustment
lever and move it toward the front of the mower.
OPERATION
MOWING TIPS
Make sure the lawn is clear of stones, sticks, wires, and
other objects that could damage the lawn mower blades
or engine. Such objects could be accidentally thrown by
the mower in any direction and cause serious personal
injury to the operator and others.
For best performance, always cut off one-third or less of
the total height of the grass.
When cutting long grass, reduce walking speed to allow
for more effective cutting and a proper discharge of the
clippings.
Do not cut wet grass, it will stick to the underside of the
deck and prevent proper bagging or mulching of grass
clippings.
New or thick grass may require a higher cutting height.
Clean the underside of the mower deck after each use
to remove grass clippings, leaves, dirt, and any other
accumulated debris.
SLOPE OPERATION TIPS
See figure 8.
Slopes are a major factor related to slip and fall
accidents that can result in severe injury. Operation on
slopes requires extra caution. If you feel uneasy on a
slope, do not mow it. For your safety, do not attempt to
mow slopes greater than 15 degrees.
Mow across the face of slopes, never up and down.
Exercise extreme caution when changing direction on
slopes.
Watch for holes, ruts, rocks, hidden objects, or bumps
which can cause you to slip or trip. Tall grass can hide
obstacles. Remove all objects such as rocks, tree limbs,
etc., which could be tripped over or thrown by the blade.
Always be sure of your footing. A slip and fall can cause
serious personal injury. If you feel you are losing your
balance, release the power lever immediately.
Do not mow near drop-offs, ditches, or embankments;
you could lose your footing or balance.
FUEL AND REFUELLING
WARNING
Always handle petrol with care; it is highly flammable.
Store fuel in containers specifically designed for this
purpose.
Always refuel outdoors where there are no sparks and
flames. Do not inhale fuel vapour. Do not smoke and
stay away from open flames and sparks when filling fuel
tank or when handling fuel.
Do not let petrol or oil come in contact with your skin.
Keep petrol and oil away from the eyes. If petrol or oil
comes in contact with the eyes, wash them immediately
with clean water. If irritation is still present, see a doctor
immediately.
Clean up spilled petrol immediately.
FILLING THE TANK
See figure 5.
WARNING
Always shut off engine before fuelling. Never remove the
cap of the fuel tank or add petrol to a machine with a
running or hot engine. Move at least 9 m (30 ft) from
refuelling site before starting the engine. Do not smoke.
Failure to heed this warning could result in serious
personal injury.
WARNING
After fueling, never tilt the mower more than 25 degrees
for this could result in fuel leakage and risk of fire, etc.
1. Clean surface around fuel cap to prevent contamination.
2. Loosen fuel cap slowly to release pressure and to keep
fuel from escaping around the cap. Rest the cap on a
clean surface.
3. Carefully pour petrol into the tank. Avoid spillage.
4. Clean and inspect the gasket, then replace all fuel and
container caps securely.
5. Wipe up any fuel spillage. Move 9 m away from
refuelling site before starting engine.
NOTE: It is normal for smoke to be emitted from a new
engine during and after rst use.
ADDING/CHECKING ENGINE OIL
See figure 5.
Engine oil has a major in uence on engine performance
and service life. For general, all-temperature use, SAE
10W-30 is recommended. Always use a 4-cycle motor oil
that meets or exceeds the requirements for API service
classi cation SJ.
NOTE: Non-detergent or 2-cycle engine oils will damage
Vue de la page 6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Commentaires sur ces manuels

Pas de commentaire