Ryobi MS181 Manuel de l'opérateur télécharger pdf (Page 14)

Page 14

FEATURES

Fig. 10

DETENT STOPS ON MITER TABLE

Detent stops have been provided at 0°, 22-1/2°, 30°,

and 45°. The 22-1/2°, 30° and 45° detent stops have

been provided on both the left and right side of the

miter table.

BEVEL LOCK KNOB

The bevel lock knob securely locks your compound

miter saw at desired bevel angles. Positive stop

adjustment screws have been provided on each side

of the saw arm. These positive stop adjustment

screws are for making fine adjustments at 0° and 45°.

See pages 20 and 21.

ELECTRIC BRAKE

An electric brake has been provided to quickly stop

blade rotation after the switch is released.

FENCE

The fence on your compound miter saw has been

provided to hold your workpiece securely against

when making all cuts.

SELF-RETRACTING LOWER BLADE GUARD

The lower blade guard is made of shock-resistant,

see-through plastic that provides protection from each

side of the blade. It retracts over the upper blade

guard as the saw is lowered into the workpiece.

MOUNTING HOLES

See Figure 11.

Your compound miter saw should be permanently

mounted to a firm supporting surface such as work-

bench. Four 3/8 in. (10 mm) bolt holes have been

provided in the saw base for this purpose. Each of the

four mounting holes should be bolted securely using

3/8 in. (10 mm) machine bolts, lock washers, and hex

nuts (not included). Bolts should be of sufficient length

to accommodate the saw base, lock washers, hex

nuts, and the thickness of the workbench. Tighten all

four bolts securely.

The hole pattern for an 18-5/8 in. x 24 in. (457.2 mm x

609.6 mm) workbench is shown in Figure 11. Care-

fully check the workbench after mounting to make

sure that no movement can occur during use. If any

tipping, sliding, or walking is noted, secure the work-

bench to the floor before operating.

WARNING:

Always make sure your compound miter saw is

securely mounted to a workbench or an approved

workstand. Failure to do so could result in an

accident resulting in possible serious personal injury.

WARNING:

The operation of any saw can result in foreign objects

being thrown into your eyes, which can result in

severe eye damage. Before starting power tool

operation, always wear safety goggles or safety

glasses with side shields and a full face shield when

needed. We recommend wide vision safety mask for

use over eyeglasses or standard safety glasses with

side shields.

WARNING:

Do not attempt to modify this tool or create

accessories not recommended for use with this tool.

Any such alteration or modification is misuse and

could result in a hazardous condition leading to

possible serious personal injury.

TRIGGER LOCK

See Figure 10.

To prevent unauthorized use of your compound miter

saw, we suggest that you remove battery pack and

lock the switch in the off position. To lock the switch,

install a padlock through the hole in the switch trigger.

A lock with a shackle up to 13/64 in. (5.2 mm) diam-

eter may be used. When the lock is installed and

locked, the switch is inoperable. Store the padlock key

in another location.

PADLOCK

SWITCH TRIGGER

Fig. 11

18”

9-3/4”

3-3/4”

7/16” DIA. HOLE

18-5/8 in.

(47.3 cm)

8-5/8 in.

(21.9 cm)

5 in.

(12.7 cm)

5 in.

(12.7 cm)

4-3/4 in.

(12 cm)

4-3/4 in.

(12 cm)

24 in.

(60.96 cm)

14-7/16 in.

(36.7 cm)

7/16 in. (11 mm)

Dia. Hole

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Ryobi MS181 Manuel de l'opérateur Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à onglets Ryobi MS181