search

Ryobi MS181 Manuel de l'opérateur Page 15

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 32
  • Table des matières
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 14
Page 15
WORK CLAMP
See Figure 14.
■ Remove battery pack from saw.
WARNING:
Failure to remove battery pack from your saw
could result in accidental starting causing possible
serious personal injury.
To install work clamp, place the shaft of the clamp in
either hole in front of the miter table base. Rotate the
knob on the clamp to move it in or out as needed.
4 5
3 0
3 0
15
15
15
30
45
22.5
31.62
2
2
.5
2
2
.5
31.62
31.62
4
3 0
15
5
2
2
.5
3
1
.6
2
R
O
T
A
T
I
O
N
4
3 0
15
5
22.5
31.62
R
O
T
A
T
I
O
N
ADJUSTMENTS
WARNING:
To prevent accidental starting that could cause
possible serious personal injury, assemble all parts
to your saw before attaching battery pack. Battery
pack should never be attached to saw when you
are assembling parts, making adjustments,
installing or removing blades, or when not in use.
As mentioned previously your saw has been factory
assembled and adjusted. The dust guide or dust bag,
battery pack and blade are the only parts that have to
be installed.
DUST GUIDE
See Figure 12.
■ Remove battery pack from saw.
WARNING:
Failure to remove battery pack from your saw
could result in accidental starting causing possible
serious personal injury.
To install the dust guide, place the end marked
INSERT over the exhaust port in the upper blade
guard. Turn the guide so that the open end is facing
down or toward the rear of the saw.
DUST BAG
See Figure 13.
■ Remove battery pack from saw.
WARNING:
Failure to remove battery pack from your saw
could result in accidental starting causing possible
serious personal injury.
A dust bag is packed with your saw. It fits over the
exhaust port on the upper blade guard. To install it,
remove the dust guide from the exhaust port. Then,
EXHAUST
PORT
squeeze the two metal clips to open the mouth of the
bag and slide it on the exhaust port. Release the clips.
The metal ring in the bag should lock in one of the
grooves on the exhaust port. For more efficient
operation, empty dust bag when no more than half
full. This will permit better air flow through the bag.
EXHAUST
PORT
DUST BAG
METAL CLIPS
DUST GUIDE
Fig. 14
WORK CLAMP
KNOB
Fig. 12
Fig. 13
Vue de la page 14
1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 31 32

Commentaires sur ces manuels

Pas de commentaire
Produits connexes et manuels pour Scies à onglets Ryobi MS181
Scies à onglets Ryobi TS1550 Manuel de l'opérateur   (26 pages)
Scies à onglets Ryobi TS230 Manuel de l'opérateur   (28 pages)
Scies à onglets Ryobi TS1351 Manuel de l'opérateur   (28 pages)
Scies à onglets Ryobi TSS120L Manuel d'utilisation et d'entretien    (104 pages)
  • Beta Three Baldwin Boxall E-flite Artwizz Beamz
  • Anton/Bauer Chargeurs de batteries pour voitures HP Cadres photo numériques Hitachi Disques durs internes Denon DJ Contrôleurs de DJ Keys Fitness Conditionnement physique, gymnastique et musculation
  • LG LV640S Thomson 40UZ7766 Samsung GT-P5100 Samsung GT-I9295 Samsung SGH-C266
  • Motorola H385 Manuel de l'utilisateur American DJ DCD-PRO300 Spécifications Aeg-Electrolux SZ91840-5I Manuel de l'utilisateur BMW Z4 Informations techniques LG ND5530 Manuel de l'utilisateur