Ryobi MS181 Manuel de l'opérateur télécharger pdf (Page 4)

Page 4

■ NEVER LEAVE TOOL RUNNING UNAT-

TENDED. REMOVE BATTERY PACK. Do not

leave tool, move workpiece or make adjustments

until it comes to a complete stop.

■ FIRMLY CLAMP OR BOLT your miter saw to a

workbench or table at approximately hip height.

■ USE ONLY CORRECT BLADES. Do not use

blades with incorrect size holes. Never use blade

washers or blade bolts that are defective or

incorrect. The maximum blade capacity of your

saw is 8-1/4 in. (209.6 mm).

■ KEEP BLADES CLEAN, SHARP AND WITH

SUFFICIENT SET. Sharp blades minimize

stalling and kickback.

■ DO NOT REMOVE THE SAW'S BLADE

GUARDS. Never operate the saw with any guard

or cover removed. Make sure all guards are

operating properly before each use.

■ KEEP HANDS AWAY FROM CUTTING AREA.

Keep hands away from blades. Do not reach

underneath work or around or under the blade

while blade is rotating. Do not attempt to remove

cut material when blade is moving.

■ BLADE COASTS AFTER TURN OFF.

■ DO NOT ABUSE CHARGER CORD. Never yank

cord to disconnect it from receptacle. Keep cord

from heat, oil, and sharp edges.

■ INSPECT CHARGER CORD PERIODICALLY

and if damaged, have repaired at your nearest

authorized service center.

■ DO NOT USE TOOL IF SWITCH DOES NOT

TURN IT ON AND OFF. Have defective switches

replaced by an authorized service center.

■ KEEP TOOL DRY, CLEAN, AND FREE FROM

OIL AND GREASE. Always use a clean cloth

when cleaning. Never use brake fluids, gasoline,

petroleum-based products, or any solvents to

clean tool.

■ ALWAYS SUPPORT LONG WORKPIECES to

minimize risk of blade pinching and kickback.

Saw may slip, walk, or slide while cutting long or

heavy boards.

■ BEFORE MAKING A CUT, BE SURE ALL

ADJUSTMENTS ARE SECURE.

■ AVOID CUTTING NAILS. Inspect for and

remove all nails from lumber before cutting.

■ ALWAYS USE A CLAMP to secure the work-

piece when possible.

■ NEVER TOUCH BLADE or other moving parts

during use.

■ NEVER START A TOOL WHEN THE BLADE IS

IN CONTACT WITH WORKPIECE. Allow motor

to come up to full speed before starting cut.

■ MAKE SURE THE MITER TABLE AND SAW

ARM (BEVEL FUNCTION) ARE LOCKED IN

POSITION BEFORE OPERATING YOUR SAW.

Lock the miter table by securely tightening the

miter lock handle. Lock the saw arm (bevel

function) by securely tightening the bevel lock

knob.

■ NEVER USE A LENGTH STOP ON THE FREE

SCRAP END OF A CLAMPED WORKPIECE.

NEVER hold onto or bind the free scrap end of

the workpiece in any operation. If a work clamp

and length stop are used together, they must

both be installed on the same side of the saw

table to prevent the saw from catching the loose

end and kicking up.

■ NEVER cut more than one piece at a time. DO

NOT STACK more than one workpiece on the

saw table at a time.

■ NEVER PERFORM ANY OPERATION "FREE-

HAND". Always place the workpiece to be cut on

the miter table and position it firmly against and

parallel to the fence as a backstop. Always use

the fence.

■ NEVER hand hold a workpiece that is too small

to be clamped. Keep hands clear of the no hands

zone.

■ NEVER reach behind, under, or within three

inches (76 mm) of the blade and its cutting path

with your hands and fingers for any reason.

■ NEVER reach to pick up a workpiece, a piece of

scrap, or anything else that is in or near the

cutting path of the blade.

■ AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slip could cause

your hand to move into the blade. ALWAYS

make sure you have good balance. NEVER

operate your miter saw on the floor or in a

crouched position.

■ NEVER stand or have any part of your body in

line with the path of the saw blade.

■ ALWAYS release the power switch and allow the

saw blade to stop rotating before raising it out of

the workpiece.

■ DO NOT TURN THE MOTOR SWITCH ON AND

OFF RAPIDLY. This could cause the saw blade

to loosen and could create a hazard. Should this

ever occur, stand clear and allow the saw blade

to come to a complete stop. Disconnect your saw

from the power supply and securely retighten the

blade bolt.

RULES FOR SAFE OPERATION

1 2 3 4 5 6 7 8 9 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Ryobi MS181 Manuel de l'opérateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à onglets Ryobi MS181