Ryobi TS1300 Manuel de l'opérateur Page 7
- Page / 28
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Page 7
Blade Diameter..................................................................................................................................10 in. (254 mm)
Blade Arbor ........................................................................................................................................5/8 in. (16 mm)
No Load Speed ........................................................................................................................................5,000 RPM
Rating ................................................................................................................................120 Volts, 60 Hz-AC Only
Input........................................................................................................................................................ 14 Amperes
Cutting Capacity
For Both Flat And Vertical Cuts On Dimensional Lumber
90° Crosscut ................................................................................................................................ 2 x 4 and 4 x 4
2 x 6 (Flat only)
45° Miter....................................................................................................................................................... 2 x 4
Net Weight.......................................................................................................................................29 lbs. (13.2 kg.)
Arbor
The shaft on which a blade or cutting tool is mounted.
Crosscut
A cutting or shaping operation made across the grain of the
workpiece.
Freehand
Performing a cut without using a fence, miter gage, fixture,
work clamp, or other proper device to keep the workpiece
from twisting during the cut.
Gum
A sticky, sap based residue from wood products.
Miter Cut
A cutting operation made with the wood at any angle other
than 90 degrees to the fence.
Resin
A sticky, sap base substance that has hardened.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object in one
minute.
Saw Blade Path
The area over, under, behind, or in front of the blade. As it
applies to the workpiece, that area which will be, or has been,
cut by the blade.
Set
The distance that the tip of the sawblade tooth is bent (or set)
outward from the face of the blade.
Throw-Back
Throwing of a workpiece in a manner similar to a kickback.
Usually associated with a cause other than the kerf closing,
such as a workpiece not being against the fence, being
dropped into the blade, or being placed inadvertently in
contact with the blade.
Through Sawing
Any cutting operation where the blade extends completely
through the thickness of the workpiece.
Workpiece
The item on which the cutting operation is being done. The
surfaces of a workpiece are commonly referred to as faces,
ends, and edges.
No Hands Zone
The area between the marked lines on the left and right side
of the miter table base. This zone is identified by no hands
zone labels placed inside the marked lines on the miter table
base. The operator's hands must stay clear of this area
during any operation of the saw.
PRODUCT SPECIFICATIONS
GLOSSARY OF TERMS FOR WOODWORKING
- OPERATOR'S MANUAL 1
- 10 in. (254 mm) Miter Saw 1
- TABLE OF CONTENTS 2
- DOUBLE INSULATION 3
- IMPORTANT 3
- RULES FOR SAFE OPERATION 3
- READ ALL INSTRUCTIONS 4
- For Miter Saws 6
- SAVE THESE INSTRUCTIONS 6
- PRODUCT SPECIFICATIONS 7
- See Figure 3 10
- See Figure 4 10
- See Figure 5 10
- See Figure 6 11
- See Figures 10, 11, and 12 12
- See Figure 7 12
- See Figure 8 12
- See Figure 9 12
- See Figure 11 13
- See Figure 10 13
- See Figure 12 13
- WARNING: 14
- See Figures 13 - 16 15
- See Figure 16 15
- See Figures 17 - 20 16
- See Figure 20 16
- See Figure 21 17
- See Figure 22 18
- See Figures 24 and 25 18
- See Figure 23 18
- See Figure 26 20
- CAUTION: 21
- See Figure 27 22
- PROBLEM CAUSE SOLUTION 23
- TROUBLESHOOTING 23
- FIGURE A 24
- FIGURE A PARTS LIST 25
- FIGURE B 26
- FIGURE B PARTS LIST 27
- Model TS1300 28
Produits connexes et manuels pour Scies à onglets Ryobi TS1300
(22 pages)
(104 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.942 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels