search

Ryobi TS1344L Manuel de l'opérateur Page 15

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 30
  • Table des matières
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 14
15
INSTALLING BATTERIES FOR LASER
See Figure 11.
Remove screw from battery compartment cover using
the Phillips end of the supplied blade wrench. Remove
cover and set aside.
Install two AAA batteries according to polarity indicators
inside the battery compartment.
Replace the battery compartment cover. Reinstall screw
and tighten securely.
DANGER:
Laser radiation. Avoid direct eye contact with light source.
WARNING:
Use of controls, adjustments, or performance of pro-
cedures other than those specified here can result in
hazardous radiation exposure.
ALIGNING THE LASER GUIDE LINE
See Figure 12.
Unplug the saw. Draw a line on the workpiece. When the
laser guide switch is turned on it will generate a red line on
the work surface. This line will let you see your mark and the
laser guide line at the same time, and will assist you in lining
up the mark for more accurate cutting of the workpiece.
Align the laser line and the mark with the blade at the up-
permost position. Once both lines are in alignment, do not
move the workpiece.
Remove the padlock then plug the saw into the power source.
Make several practice cuts on different styles and thickness
of material. Repeat the steps above as necessary.
Removing Your Mark:
Position the laser line near the left edge of your mark on the
work surface in order to remove the mark.
To Cut Your Mark:
Position the laser line near or over your mark on the work
surface in order to cut the mark.
To Leave Your Mark:
Position the laser line near the right edge of your mark on
the work surface in order to leave the mark.
After you have become familiar with using the laser guide,
you will be able to remove, cut, or leave your mark on the
work surface. Practice will teach you the correct position for
aligning the laser line with your mark.
Fig. 12
LASER
LINE
A
V
O
I
D
E
X
P
O
S
U
R
E
:
L
A
S
E
R
R
A
D
I
A
T
I
O
N
E
M
I
T
T
E
D
F
R
O
M
T
H
I
S
A
P
E
R
T
U
R
E
L
O
C
K
T
R
I
G
G
E
R
P
R
I
O
R
T
O
A
D
J
U
S
T
I
N
G
L
A
S
E
R
W
A
R
N
I
N
G
ASSEMBLY
BATTERIES
COMPARTMENT
COVER
SCREW
Fig. 11
Vue de la page 14
1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 29 30

Commentaires sur ces manuels

Pas de commentaire
Produits connexes et manuels pour Scies à onglets Ryobi TS1344L
Scies à onglets Ryobi TS1350 Manuel de l'opérateur   (28 pages)
Scies à onglets Ryobi TS1300 Manuel de l'opérateur   (28 pages)
Scies à onglets Ryobi TS1302 Manuel de l'opérateur   (22 pages)
Scies à onglets Ryobi MS181 Manuel de l'opérateur   (32 pages)
Scies à onglets Ryobi TS1550 Manuel de l'opérateur   (26 pages)
Scies à onglets Ryobi TS230 Manuel de l'opérateur   (28 pages)
Scies à onglets Ryobi TS1351 Manuel de l'opérateur   (28 pages)
Scies à onglets Ryobi TSS120L Manuel d'utilisation et d'entretien    (104 pages)
  • Adaptivation Kress Huey Chiao VariPOS Rio Mobility
  • Genie Bicyclettes SMSC Non Hi-Fun Casques d'écoute mobiles Sony Accessoires pour caméras de sécurité Konica Minolta Multifonctionnels
  • Sony DSC-W530 Nokia 20 Presonus ACP22 Electrolux EGE6182NOK
  • Sony CDP-CE415 Manuel de l'utilisateur Boss GL-100 Manuel de l'utilisateur Electrolux ESF8635ROX Manuel de l'utilisateur Evga P55 SLI Manuel de l'utilisateur Yamaha RX-V1900 Manuel