Ryobi YN200BND Manuel de l'opérateur télécharger pdf (Page 11)

11 - English

OPERATION

DRIVING A FASTENER

See Figure 8, page 16.

WARNING:

Never wedge or hold back the workpiece contact

mechanism during operation of the tool. Doing so could

result in possible serious injury.

SINGLE SEQUENTIAL ACTUATION

Single sequential actuation provides accurate fastener

placement.

Connect the tool to the air supply.

Grip the tool firmly to maintain control. Position the nose

of the tool onto the work surface.

Push the tool against the work surface to depress the

workpiece contact.

Pull the trigger to drive a fastener.

Allow the tool to recoil away from the work surface as the

fastener is driven.

WARNING:

During normal use the tool will recoil immediately

after driving a fastener. This is a normal function of

the tool. Do not attempt to prevent the recoil by holding

the nailer against the work. Restriction to the recoil can

result in a second fastener being driven from the nailer.

Grip the handle firmly, let the tool do the work, and do

not place second hand on top of tool or near exhaust at

any time. Failure to heed this warning can result in serious

personal injury.

SETTING THE AIR PRESSURE

The amount of air pressure required will depend on the size

of the nail and the workpiece material.

Begin testing the depth of drive by driving a test nail into the

same type of workpiece material used for the actual job.

Drive a test nail with the air pressure set at 90-95 psi. Raise

or lower the air pressure to find the lowest setting that will

perform the job with consistent results.

It may be possible to achieve the desired depth with air

pressure adjustments alone. If finer adjustments are needed,

use the drive depth adjustment on the tool.

DRIVE DEPTH ADJUSTMENT

See Figure 9, page 16.

The driving depth of the nail may be adjusted. It is advisable

to test the depth on a scrap workpiece to determine the

required depth for the application.

To determine depth of drive, first adjust the air pressure and

drive a test nail. To achieve the desired depth, use the drive

depth adjustment on the tool.

Disconnect the tool from the air supply.

Turn the depth selector left or right to change the driving

depth.

Reconnect the tool to the air supply.

Drive a test nail after each adjustment until the desired

depth is set.

WARNING:

Disconnect the tool from the air supply before removing

nails. Failure to do so could result in serious personal

injury.

REMOVING NAILS FROM THE TOOL

See Figure 10, page 16.

Disconnect the tool from the air supply.

To remove a strip of nails from the tool, depress the latch

located at the rear of the magazine and slide the magazine

open.

 Remove the nail strip.

To close the magazine, depress the latch and push the

magazine forward. Release the latch to hold the magazine

in place.

CLEARING A JAMMED FASTENER

See Figure 11, page 16.

WARNING:

Disconnect the tool from the air supply before clearing a

jammed fastener. Failure to do so could result in serious

personal injury.

If a nail or fastener becomes jammed in the tool, disconnect

the air hose and keep the tool pointed away from you while

clearing the jam.

Disconnect the tool from the air supply.

Openmagazineandremovefastenersfromthetool.

Pulluponthelatchandopenthejamrelease.

Insert a flat blade screwdriver into the driving mechanism

and push the driver mechanism back, freeing the fastener

jam.

Remove the bent fastener.

Close the jam release and latch.

Reconnect the tool to the air supply.

Reinstall fasteners and close the magazine.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 43 44

Commentaires sur ces manuels

Pas de commentaire

Ryobi YN200BND Manuel de l'opérateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Pistolet à clous Ryobi YN200BND