Ryobi ERT2100VK Guide de l'utilisateur télécharger pdf (Page 11)

282

axminster.co.uk/signup for our exclusive email offersCall 03332 406406

Accessories

Kitchen Worktop Jigs

ColorFill performs many tasks; bonds the joint together, seals the

joint against water and domestic detergents and can be colour

matched to the worktop so making the ﬁ nished joint almost

invisible. It will also repair scratches and chips in laminate and

melamine surfaces. Scientiﬁ cally formulated and tested to resist

moisture, detergent and other household products as efﬁ ciently as

the laminate and will withstand heat and direct sunlight. Although

it is recommended that hot pans and dishes from the oven should

not be placed over joints. ColorFill requires no mixing, is easy to

apply and is available in handy sized 25g tubes sufﬁ cient for one

worktop joint and 20ml of clean-up solvent is included.

Unika ColorFill

Worktop Sealer and

Repair

Black Granite £7.44 £6.20 952234

Block Beech £7.44 £6.20 952235

Soft White £7.44 £6.20 952236

Inc.vat Ex.vat Code

This patented plinth lock system is a unique way of ﬁ rmly securing

kitchen plinths, corner posts, ﬁ ller panels as well as many other

applications. This concealed ﬁ xing is quick and easy to ﬁ t and

eliminates unsightly screw ﬁ xings, maintaining a 90° solid ﬁ tting.

Simply line up and screw each half of the plinth lock onto the work

using two screws in each, the plinth is then pushed in place securely,

wedging the joint tightly together. Supplied as a pack of six.

Unika Plinth Lock

Plinth Lock (6) £5.94 £4.95 952238

Inc.vat Ex.vat Code

Kitchen Worktop Jigs

Router not included

Axminster Extra

Kitchen Worktop Jig

The Axminster extra kitchen worktop jig was designed by us after a studying the features other worktop jigs were offering. This resulted in

several innovations not found on similar jigs of this type. With precise positioning and sighting of the cut line, this postform jig is intended

for the discerning user who requires an easy to use jig that gives consistent results. It will accept a worktop up to 700mm wide with a

jointing facility at 22.5° and 45°. The main template body is 16mm thick synthetic resin laminate plate, machined to very ﬁ ne tolerances

which will guide your router accurately using a standard 30mm guide bush. Cutting errors are often caused by an inaccurately located

guide bush. To eliminate this we provide a check centre for the guide bush to ensure its precise concentricity when mounting and

securing it to the router. The guide slots and preset angles are located with 10mm metal dowel pins to ensure exact positioning against

the edge of your worktops and encompass the principal angles required, plus positioning for the new style connectors and various inserts.

Flush face clamping provides a totally unimpeded working face whilst enabling the template to be held securely to the worktop using

any combination of the eight sliding locations for the recessed clamp heads. To ensure error-free cutting of the female part of the joint so

that it perfectly matches the mating worktop we have incorporated a width measuring locator facility on this jig. Set between static dowel

pins and a sliding pin, the width of the top can be gauged without measuring or guesswork, providing the exact amount of cut in to

accommodate the worktop end. The jig also has 3 circular holes to cut pockets at 50, 70 and 80mm diameter, 3 preset connector pockets

with 200mm spacing, a 45° corner guide edge, Long sweep radius guide edge (approximate 460mm radius), 100mm radius guide edge

and a single uninterrupted guide edge 880mm long. Numerous slots to enable sub-surface clamping (using Axminster clamp and head

combination), variable positioning to set length of butt socket joint for 45° joining, positioning for setting length of butt socket joint for

22.5° joining and also positioning (using dowel pins) to set jig long

edges to 22.5°, 30° and 45°. All machining is carried out using a

30mm guide bush and a 1/2” diameter router cutter. Supplied with

step by step instructions for perfect results.

AWTJ1 Kitchen Worktop Jig £187.94 £156.62 702284

30mm Guide Bush £11.75 £9.79 211308

Replacement Pins £9.95 £8.29 952462

Inc.vat Ex.vat Code

The Multipurpose Jig is designed for use with a wide variety of

worktops. As the jig will cut an inset of 10mm and 23mm it can be

used to cut the following worktops: composite, solid wood, small

radius (less than 6mm) laminate worktops and standard radius

(more than 6mm) laminate worktops. It cuts 300mm, 400mm,

500mm, 600mm, 616mm, 650mm and 700mm worktops. Features

include cuts 90° left and right joints, corner cooking solution

and 3 bolt slots. All that is required to complete the job is a 1/2” x

50mm straight router cutter, 30mm guide bush and a couple of

F-Clamps.

Multipurpose Worktop Jig

Worktop Jig £79.94 £66.62 702801

30mm Guide Bush £11.75 £9.79 211308

Inc.vat Ex.vat Code

The Multipurpose Jig is designed for use with a wide variety of

worktops. As the jig will cut an inset of 10mm and 23mm it can be

used to cut the following worktops: composite, solid wood, small

radius (less than 6mm) laminate worktops and standard radius

(more than 6mm) laminate worktops. It cuts 300mm, 400mm,

500mm, 600mm, 616mm, 650mm and 700mm worktops. Features

include cuts 90° left and right joints, corner cooking solution

and 3 bolt slots. All that is required to complete the job is a 1/2” x

50mm straight router cutter, 30mm guide bush and a couple of

F-Clamps.

Multipurpose Worktop Jig

Worktop Jig

Inc.vat

Quick and easy to apply with strong adhesion, creating a

permanent bond to materials like wood, metal, varnish and

any low energy surfaces. Ideal for attaching worktop edging

and trims. It has a good resistance to extreme temperatures,

chemicals and solvents, humidity and UV radiation with a

high shear resistance. Because of high adhesive mass, it is also

appropriate for rough or structured surfaces. Consisting of a hard

PVC ﬁ lm carrier, layered on both sides with a modiﬁ ed acrylate

adhesive. The adhesive is lined with a double-sided silicone paper.

Temperature resistant -40° to +70°C.

5 metre length X 40mm width

HD Double Sided Tape £5.24 £4.37 952233

Inc.vat Ex.vat Code

Unika Heavy Duty

Double Sided 5m Tape

This self-adhesive tape and sheet will

protect edges and faces against radiant

heat on surfaces like worktops, shielding

the edges of a hob cut out or worktop

underside from heat from a cooker or

dishwasher. Available as heat reﬂ ective aluminium tape 50mm

wide x 3m or a sheet 1m x 600mm.

Tape - 50mm x 3m £2.45 £2.04 952231

Sheet 1m x 600mm £3.95 £3.29 952232

Inc.vat Ex.vat Code

Unika Heat Reflective

Aluminium Tape and Sheet

Plated steel connectors for a ﬁ rm joint between sections of worktop.

Connectors (10) £3.95 £3.29 910194

Connectors (100) £35.95 £29.96 717018

Inc.vat Ex.vat Code

Worktop

Connectors

• Fast, strong and secure worktop

connectors

• Use a drill driver with a hex bit to install

• Cost effective solution for kitchen

worktop joints

• Requires 4mm or 5mm hex bit for

tensioning

• Zinc ﬁ nish

Zipbolt Worktop Connectors

Worktop Connector 170mm £2.45 £2.04 504439

Worktop Connector 85mm £2.24 £1.87 504438

Mini Benchtop Connector £2.64 £2.20 504434

Inc.vat Ex.vat Code

This very accurate marker is basically a large square with a 45°

angle and will assist in all marking out tasks especially when

ﬁ tting a kitchen. It is designed for the positioning of apertures,

door handles, and 45° and 22.5° angles. Speciﬁ c holes can be

marked up from the edge of your worktop for cut-outs, plus it

has a pre-determined slot with measurements for more sizes.

Designed especially for kitchen ﬁ tters, it will also have a general

use in the workshop for marking panels.

Unika TopMarker £56.94 £47.45 503841

Inc.vat Ex.vat Code

Unika TopMarker

Professional Ear Defenders £18.44 £15.37 210774

Inc.vat Ex.vat Code

• 31dB protection against your

machinery noise

• Ear cups have super soft cushions

• Very comfortable; easy to adjust

• Neatly folds for storage

uvex 3 Professional

Ear Defenders

07_Routing 272_299.indd 282 29/11/2013 11:36

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 27 28

Commentaires sur ces manuels

Pas de commentaire

Ryobi ERT2100VK Guide de l'utilisateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Mise en réseau Ryobi ERT2100VK