Ryobi ERT2100VK Guide de l'utilisateur télécharger pdf (Page 6)

Section

Order online axminster.co.uk/routing

277

Jigs

Axminster

Universal Hinge Jig

To speed up the ﬁ tting of hinges, this simple device will soon

pay for itself in the time saved when cutting the recesses. Using

suitable guide bush cutter combinations, hinge recesses of

50mm, 75mm and 100mm can be routed quickly and accurately.

Suggested combinations are 26mm guide bush used with a

20mm cutter for 100mm or 50mm hinges; 40mm guide bush with

a 9mm cutter for 75mm or 25mm hinges. Just take out the waste

from the corners with our Axminster corner chisel 340437 and

your hinges will drop in nicely. Concealed cabinet hinges can also

be ﬁ tted by using a 24mm guide bush with a 12mm cutter giving

a 35mm hole and a 30mm guidebush with a 9mm cutter giving a

26mm hole. Full instructions supplied with jig.

ASHJ100/50 Hinge Jig £33.95 £28.29 100714

Set of 12 Guide Bushes £19.94 £16.62 340936

Inc.vat Ex.vat Code

Clamp not

supplied

Hinge Length Guide bush dia. Cutter dia. Template

100mm 26mm 20mm 106mm

75mm 40mm 9mm 106mm

50mm 26mm 20mm 50mm

25mm 40mm 9mm 50mm

35mm dia. 24mm 12mm 40mm dia.

26mm dia. 30mm 9mm 40mm dia.

The Hinge Mate Morticing Jig, based on the very popular ProGrip

clamping system, offers a secure and accurate method of routing

out a variety of recesses, including those for butt hinges, locks,

lock plates, stopped housings and mortices. The jig consists

of two cam clamping arms, a cross bar and an adjustable stop

and, once assembled, can be quickly set up to rout a wide range

of recess sizes. Although bearing-guided trimming cutters can

be used, we recommend the use of a suitable guide bush and

straight cutter. Full instructions on setting the jig and on the

choice of cutter and guide bush are included.

Morticing System £55.94 £46.62 200204

Inc.vat Ex.vat Code

ProGrip

Hinge Mate

Morticing

System

Tools do not get any simpler than

this one. A high quality tungsten

steel corner chisel is sharpened

in-cannel fashion and held into

a spring-loaded steel bodied jig.

Absolutely perfect for knocking

the rounded corners out of a

routed hinge recess; simply

place the chisel into the rounded

corner, hit once with a hammer

or mallet and then pare out the

waste for a perfect cut every time!

Corner Chisel £6.74 £5.62 340437

Inc.vat Ex.vat Code

The Corner Chisel

Easy to use with minimal set up this two piece hinge jig allows

you to produce clean and accurate hinge recesses in both the

door and frame, with a high degree of accuracy, with the use of

a router. On site or in the workshop, it takes away the need for

conventional marking out.

The template is for door sizes up to 2,100mm in height, (with a

minimum thickness of 16mm). Fitted with four apertures it will

even cope with ﬁ re door requirements; the same template being

used for door and frame without the need for any adjustment.

Fit the router with the supplied 16mm guide bush; a 12mm

diameter long reach cutter is available separately. Adjustable

blocks positioned within the apertures allow for variations to

both hinge position and hinge length. Stops locate the jig on

an edge to give the recess width, and a swivel plate on the top

of the jig is used to position the jig and give a set 2mm spacing

between the door and the head of the frame. After routing, the

recess is simply squared off by hand or with a corner chisel.

Suitable for hinges 67mm (2.5/8”) to 125mm (5”) long, 9.5mm

(3/8”) to 35mm (1.3/8”) wide and for doors 16mm (5/8”) to 38mm

(1.3/4”) thick. The jig is designed for use with 1/4” shank routers

due to their compact size. The 16mm guide bush will ﬁ t a large

range of routers, however some may require a universal base.

Supplied with four apertures, bradawl with spacers, 16mm

guide bush (universal base maybe required), T-handle hex

key, 4mm spacing gauge and fabric storage case.

Two Part Hinge Jig £224.94 £187.45 501664

Long Reach Cutter £24.95 £20.79 300276

Inc.vat Ex.vat Code

Trend 2

Piece Hinge

Jig Set A

The Door Lock Jig uses a set of interchangeable templates to

produce the mortice and faceplate recesses for all popular sizes

of door lock with up to 3” deep mortices and 1” wide faceplates.

Deeper mortices can be achieved with a suitable size of auger

bit. Also suits the faceplate on a 1” mortice latch. The jig requires

a router ﬁ tted with a 30mm guide bush and 12mm diameter

long reach cutter. If deep mortices are to be cut then the use

of a 1/2” shank router is recommended. Comes with a range of

templates to suit most popular locks and latches, also a chart for

the selection of the correct template.

Door Lock Jig £99.95 £83.29 600188

1/4” Cutter 12mm x 70mm £22.94 £19.12 910103

1/2” Cutter 12mm x 115mm £29.94 £24.95 910104

Inc.vat Ex.vat Code

Trend Door Lock Jig

Jigs

Some routers can be difﬁ cult to match up with suitable guide

bushes and a universal sub-base can be the only solution. A

round base can be preferable in many circumstances too. The

UJK technology sub-base is precision machined from aluminium

and ﬁ tted with a low friction surface for ease of use. It is designed

to accept standard Axminster or Trend style guide bushes and

holes for these are drilled with an M4 thread. It is also designed

for mounting to a very wide range of different routers including

Bosch, Makita, Elu, Dewalt, Festool, Trend, Ryobi and Hitachi

models to name a few and a ﬁ xing kit is included to cover a

variety of thread types. 176mm diameter x 7mm thickness.

UJK Techology

Universal Sub-Base

Aluminium Sub-Base £24.95 £20.79 718650

Inc.vat Ex.vat Code

Guide bush

not included

For producing closed tread and open

tread staircases, this professional jig

is easy to set up using the integral,

reversible setting bar. Supplied with

a universal sub-base and four radius

bushes (in two sets) to achieve the

correct router offset. Suitable cutters are available

separately (16mm diameter for 22mm and 25.4mm tread thickness

and 22mm diameter for 28.1mm and 32mm tread. The jig is simply

located using you own G clamps. Full instructions supplied.

Staircase Jig £95.94 £79.95 910198

Inc.vat Ex.vat Code

Axminster

Staircase Jig

correct router offset. Suitable cutters are available

separately (16mm diameter for 22mm and 25.4mm tread thickness

Trend ‘A’ Staircase Jig

This jig, is an invaluable aid for routing out housings for treads and

risers on closed staircases. It is designed for use with any 1/2” shank

heavy duty router ﬁ tted with a 30mm diameter guide bush, it has

a reversible fence for exact pairing of the stair strings. Supplied

complete with spanners, lock nuts and full instructions.

Staircase jigs are a well proven means of routing out stair housings

quickly and accurately, they can easily pay for themselves in the

speed of production and quality of the end result. Suitable Axcaliber

cutters are available for this jig as follows: 22mm tread thickness

select 14mm diameter cutter, 25.4mm select 16mm diameter,

28.1mm select 19mm diameter and 32mm select 22mm diameter.

Staircase Jig £159.95 £133.29 900225

Inc.vat Ex.vat Code

A choice of cutters for Staircase Jigs to suit various string

and tread thicknesses. The cutters are dovetailed at an angle

of 5° resulting in tight ﬁ tting joints between the treads/

risers and strings when assembled and wedged. Select the

diameter of cutter to suit your tread thickness and stair jig.

Cutter 14mm diameter £11.45 £9.54 666073

Cutter 16mm diameter £12.44 £10.37 666072

Cutter 19mm diameter £13.44 £11.20 666071

Cutter 22mm diameter £14.45 £12.04 666070

Inc.vat Ex.vat Code

Axcaliber Dovetail Cutters

for Stair Jigs - 1/2”(12.7mm)

07_Routing 272_299.indd 277 29/11/2013 11:30

1 2 3 4 5 6 7 8 9 10 11 ... 27 28

Commentaires sur ces manuels

Pas de commentaire

Ryobi ERT2100VK Guide de l'utilisateur Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Mise en réseau Ryobi ERT2100VK