search

Ryobi r163 Manuel de l'opérateur Page 11

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 20
  • Table des matières
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 10
11
OPERATION
WARNING:
If the collet nut is not securely tightened, the bit may
detach during use, causing serious personal injury.
WARNING:
Never use bits which are larger in diameter than the open-
ing in the router subbase. These situations could cause
possible loss of control or create other hazardous condi-
tions that could cause possible serious personal injury.
CAUTION:
To prevent damage to the spindle or spindle lock, always
allow motor to come to a complete stop before engaging
the spindle lock.
WARNING:
If you are changing a bit immediately after use, be careful
not to touch the collet nut, bit, or collet with your hands or
fingers. You will get burned because of the heat buildup
from cutting. Always use the wrench provided.
WARNING:
Bit continues to rotate after the router has been turned off.
To avoid injury, wait until the bit has come to a complete
stop before removing router from the workpiece.
INSTALLING/REMOVING BITS
See Figure 3.
Unplug the router.
To install the bit:
Push the spindle lock down and in, holding it into
place.
Loosen the collet nut and remove the bit.
Insert the bit until it is approximately 1/8 in. to 1/4 in. away
from the collet nut face.
NOTE: Make sure that the collet always clamps the shank
(non-cutting end) of the bit.
Tighten the collet nut securely by turning it clockwise with
the wrench provided.
Release the spindle lock.
To remove the bit:
Push the spindle lock down and in, holding it into
place.
Loosen the collet nut and remove the bit.
Release the spindle lock.
Fig. 3
LED WORKLIGHT
See Figure 4.
The two LED worklights on the base of the router motor
will come on when the ON/OFF switch is in the ON ( I )
position. This provides additional lighting on the surface of
the workpiece for operation in lower-light areas.
TO
LOOSEN
SPINDLE
LOCk
TO
TIgHTEN
COLLET NuT
Fig. 4
LED
WOrkLIgHT
Vue de la page 10
1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 19 20

Commentaires sur ces manuels

Pas de commentaire
Produits connexes et manuels pour Mise en réseau Ryobi r163
Mise en réseau Ryobi RT501W Spécifications   (28 pages)
Mise en réseau Ryobi RT401W Manuel de l'opérateur   (24 pages)
Mise en réseau Ryobi RE601 Manuel d'utilisateur   (2 pages)
Mise en réseau Ryobi R180 Manuel de l'opérateur   (14 pages)
  • Mr. Heater Toontrack Duck AGM Electronics Ge-security
  • Best Non Premier Mounts Accessoires de fixation aux murs et aux plafonds Logitech Claviers d'appareils mobiles NEC Affichages publics Avermedia Syntoniseurs de télévision par ordinateur
  • Bissell 67F8 GE WJRE5550KWW KitchenAid KHSP5 86510 Konica-minolta bizhub 185 Supermicro X7SPA-HF
  • Panasonic NVGS330 Instructions d'exploitation Philips QC5170/00 Manuel de l'utilisateur Yamaha YSP-4100 Manuel de l'utilisateur Sony ICF-C317 Manuel de l'utilisateur Acer B247W Manuel de l'utilisateur