Ryobi P620 Manuel d'utilisateur télécharger pdf (Page 7)

English

FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR

OPERATION

To do this, fill a 1 liter container with the required paint.

Then use the viscosity cup supplied to add 100 ml of

required thinner. Stir the contents thoroughly, measure

the viscosity using the viscosity chart above. If paint

requires further thinning then repeat the above step.

NOTE: Some paints are outside the ranges listed above.

Please contact our helpline for further information.

FILLING SPRAYER WITH PAINT/STAIN

See Figure 3-4.

Remove and discard any skin that has formed on top of

the paint or stain, then thoroughly mix the material in its

original container before beginning.

NOTE: Older containers of stain and paint may need to

be strained before use.

Q Remove the battery pack from the sprayer.

Q Remove the quick-lock container by twisting clockwise

so that the arrow on the container lines up with the

“unlock” symbol on the lid.

Q Fill the container with paint or stain as desired. Do not

fill above the max fill mark on the container.

Q Reinstall the container on the sprayer and twist

counterclockwise so that the arrow on the container

lines up with the “lock” symbol on the lid.

SELECTING THE PROPER SPRAY TIP

See Figure 5.

Use the Round Tip for thinner diluted paints

and stains. This tip sprays in a round pattern.

Ideal for outdoor fence spraying.

Use the Fan Tip for thicker or non diluted

paints. This tip sprays in a wide pattern,

giving a fine professional finish. It can be

adjusted from horizontal to vertical. Ideal for

indoor wall spraying.

To switch tips:

Q Remove the battery pack from the sprayer.

Q Remove the installed tip by turning it counter-

clockwise.

Q Install the desired tip and rotate clockwise to tighten

securely.

NOTE: The tip should be tightened securely by

hand. A too loose or overtightened tip may cause the

sprayer to leak or be damaged.

To change direction of fan tip from Horizontal to

Vertical:

Q Slightly loosen the fan tip by rotating counterclockwise

1/4 turn.

Q Rotate the adjusting arm 1/4 turn in the direction

needed to switch the direction of the tip spray.

Q While holding the adjusting arm in position, rotate the

fan tip clockwise until securely tightened.

OPERATING THE SPRAYER

See Figure 6-9.

Q Place a line of lubricant on the piston. To gain access

to the piston, follow the instructions in Cleaning the

Sprayer for Storage in the Maintenance section of

this manual.

Q Ensure surface to be painted is free of dust, dirt, and

grease.

Q Mask or cover any areas not intended to be painted

or stained. Be aware of wind that may cause your

paint or stain to spray into areas not desired. Always

use drop cloths or other cover to protect areas that

are not intended to be painted or stained.

Q Fill the quick-lock container with no more than 1 liter

of desired paint or stain.

NOTE: After every 4 refills of the quick-lock

container, add a line of lubricant to the piston. See

Cleaning the Sprayer for Storage for instructions

on disassembling the sprayer to gain access to the

piston.

Q Select the proper spray tip for desired spray pattern.

Q Install the battery pack in the sprayer.

Q Pull the switch trigger to spray paint. Release the

switch trigger to stop paint spray.

Q Practice spraying on a piece of scrap material to test

your spray pattern and to prime the pump before

beginning. If you cannot get a good spray pattern with

an even amount of paint or stain throughout, refer to

either the Dilution section or Troubleshooting section

later in this manual.

NOTE: The pump must be primed after every paint

change and at first use after storing. Spray paint at a

scrap surface for at least 20 seconds to prime.

Q To create an even coating over the entire surface:

• Move your arm at a steady rate of speed and make

sure to move your entire arm, not just your wrist.

• Keep the sprayer an even distance from the area

being sprayed, which should be between 20 to 25

cm from the tip of the sprayer to the surface being

sprayed.

• Depress the trigger to begin the spray off the

material you want to paint. Operate the sprayer in

straight horizontal or vertical strokes across the

surface being painted, then release the trigger off

the material to end the stroke.

NOTE: For spray quality consistency when using

thinner paints, it may be necessary to keep the

trigger depressed between strokes.

Q When finished, remove the battery pack, return any

unused paint or stain to its original container, and

thoroughly clean the sprayer.

1 2 3 4 5 6 7 8 9 10

Commentaires sur ces manuels

Pas de commentaire

Ryobi P620 Manuel d'utilisateur Page 7

Commentaires sur ces manuels