Ryobi PCN3840-RY74005D Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outil à essence Ryobi PCN3840-RY74005D. Ryobi PCN3840-RY74005D User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 20
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
OPERATOR’S MANUAL
PCN3840 - RY74005D - 406 mm (16 in.) 38cc Chainsaw
PCN4545 - RY74007D - 457 mm (18 in.) 45cc Chainsaw
Your new chainsaw has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation,
and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before
using this product.
Thank you for buying a Ryobi chainsaw.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Vue de la page 0
1 2 3 4 5 6 ... 19 20

Résumé du contenu

Page 1 - OPERATOR’S MANUAL

OPERATOR’S MANUALPCN3840 - RY74005D - 406 mm (16 in.) 38cc ChainsawPCN4545 - RY74007D - 457 mm (18 in.) 45cc ChainsawYour new chainsaw has been engine

Page 2 - INTRODUCTION

10UKNOTE: Do not use dirty, used or otherwise contaminated oils.Damage may occur to the oil pump, bar, or chain.1. Carefully pour the bar and chain oi

Page 3 - GENERAL SAFETY RULES

11UK Maintain a proper grip on the saw whenever the engine isrunning. The fingers should encircle the handle and thethumb be wrapped under the ha

Page 4 - SPECIFIC SAFETY RULES

12UKADJUSTING IDLING SPEEDSee Figure 24. If the engine starts, runs, and accelerates but will not idle,turn the idling speed screw “T” clockwise

Page 5

On large diameter trees, stop the back cut before it is deepenough for the tree to either fall or settle back on the stump.Then insert soft wooden or

Page 6

14UKCUTTING SPRING POLESSee Figure 37.A spring pole (A) is any log, branch, rooted stump, or saplingwhich is bent under tension by other wood so that

Page 7 - SPECIFICATIONS

15UKCHAIN MAINTENANCESee Figures 51 and 52.CAUTION:Check that the switch is in the STOP “ ” position beforeyou work on the saw.Use only a low-kick-b

Page 8 - FEATURES

16UKMAINTAINING DEPTH GAUGE CLEARANCESee Figures 51, 59, and 60. Maintain the depth gauge (A) at a clearance of 0.6 mm(0.025”). Use a depth gauge too

Page 9

17UKChoose one of the following cleaning options:9. To lightly clean, tap the filter against a smooth, flat surfaceto dislodge most saw dust and dirt

Page 10 - OPERATION

18UKRECOMMENDED BAR AND CHAIN COMBINATIONS FOR .325 LOW PROFILE .050 GAUGELength of Bar Guide Bar Part Number Chain Part Number406 mm (16 in.) 9843160

Page 11

19UK PROBLEM POSSIBLE CAUSE SOLUTIONEngine starts, runs,and accelerates butwill not idle.Engine starts and runs,but chain is not rotati

Page 12

2UK Introduction ...

Page 13

20UKSAFETY DIRECTIVEEC DECLARATION OF CONFORMITYAccording to machinery directive 98/37/EC and EMC directive 89/336/EEC - We,Ryobi Technologies Inc., 1

Page 14 - MAINTENANCE

3UKWARNING:The warnings, labels, and instructions found in thissection of the operator’s manual are for your safety.Failure to follow all instructions

Page 15

4UK KEEP ALL PARTS OF YOUR BODY away from the sawchain when the engine is running. ALWAYS CARRY THE CHAINSAW WITH THE ENGINESTOPPED AND THE BRAK

Page 16

5UKPROPER CLOTHING FOR SAFETY Wear close-fitting clothing. Always wear heavy, longtrousers, boots, and gloves. Do not wear jewellery,shorts, sand

Page 17

6UKImportant: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Properinterpretation of these symbols

Page 18 - TROUBLESHOOTING

7UKPetrol Use unleaded petrol intended for motor vehicle usewith an octane rating of 87 ([R + M] / 2) or higher.Oil Use 2-cycle oil for air cooled eng

Page 19 - WARRANTY

8UKFor your safety, study this entire manual before operating thesaw. Pay particular attention to the precautions and instructionslisted in the operat

Page 20 - EC DECLARATION OF CONFORMITY

9UKKICK-BACK PRECAUTIONSSee Figures 4 and 5.Rotational kick-back (A) occurs when the moving chain contactsan object at the Kick-back Danger Zone (B) o

Commentaires sur ces manuels

Pas de commentaire