Ryobi RY43006 Manuel de l'utilisateur

Naviguer en ligne ou télécharger Manuel de l'utilisateur pour Outil à essence Ryobi RY43006. Ryobi RY43006 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 30
  • Table des matières
  • MARQUE LIVRES
  • Noté4.6 / 5. Basé sur5 avis des utilisateurs
Vue de la page 0
SAVE THIS MANUAL FOR FUTURE REFERENCE
Your chain saw has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using
this product.
Thank you for buying a Ryobi product.
OPERATOR’S MANUAL
18 in. ELECTRIC CHAIN SAW
DOUBLE INSULATED
RY43006
Vue de la page 0
1 2 3 4 5 6 ... 29 30

Résumé du contenu

Page 1 - OPERATOR’S MANUAL

SAVE THIS MANUAL FOR FUTURE REFERENCEYour chain saw has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation

Page 2 - INTRODUCTION

10Bar Tip GuardAn attachment that may be provided on the end of the guide bar to prevent the chain at the end of the guide bar from contacti

Page 3 - GENERAL SAFETY RULES

11FEATURESFig. 5PRODUCT SPECIFICATIONSBar Length... 18 in.Chain Type ...

Page 4

12ASSEMBLYUNPACKINGThis product has been shipped completely assembled.n Carefully remove the tool and any accessories from the box. Make sure that al

Page 5

13OPERATIONAUTOMATIC CHAIN OIL SYSTEMSee Figure 6. NOTE: Chain saw comes from the factory with no bar and chain oil added.n Use Power Care Bar an

Page 6

14Fig. 8SWITCH LOCKSWITCH TRIGGERWARNING:Keep body to the left of the chain line. Never straddle the saw or chain, or lean over past the chain line.ST

Page 7

15n Maintain a proper grip on the saw whenever the unit is running. The fingers should encircle the handle and the thumb is wrapped under the handleb

Page 8 - SAVE THESE INSTRUCTIONS

16Fig. 12PROPER CUTTING STANCESee Figure 12.n Weight should be balanced with both feet on solid ground.n Keep left arm with elbow locked in

Page 9 - ELECTRICAL

17WARNING:If the tree starts to fall in the wrong direction, or if the saw gets caught or hung up during the fall, leave the saw and save yourself!n

Page 10 - GLOSSARY OF TERMS

18n Felling Backcut. The backcut is always made level and horizontal, and at a minimum of 2 in. above the horizontal cut of the notch. See Figures 14

Page 11 - FEATURES

19BUCKING LOGS UNDER STRESSSee Figures 19 - 20.When the log is supported along its entire length, it should be cut from the top or overbucking.When th

Page 12 - OPERATION

2n Introduction ...

Page 13

20LIMBINGSee Figure 21.Limbing is removing branches from a fallen tree. n Work slowly, keeping both hands on the chain saw with a firm grip. Always m

Page 14

21ADJUSTMENTSWARNING:Before performing any adjustment, make sure the tool is unplugged from the power supply. Failure to heed this warning could resul

Page 15

22REPLACING BAR AND CHAIN See Figures 27 - 31.WARNING:Before performing any maintenance, make sure the tool is unplugged from the power supply. Failur

Page 16

23n Reinstall the chain cover assembly, bushing and guide bar nut. Tighten the guide bar nut finger tight only. The bar must be free to move for tens

Page 17

24CHAIN MAINTENANCESee Figures 32 - 33.Fig. 34Fig. 33CHECK FOR WEAR OR DAMAGEUse only 3/8 in. pitch skip tooth/low-kickback(62 drivelink) chain

Page 18

25TOP PLATE FILING ANGLESee Figure 36.n CORRECT 30° - File holders are marked with guide marks to align file properly to produce correct top plate an

Page 19

26Use a Flat File and a Depth Gauge Jointer to lower all gauges uniformly. Depth gauge jointers are available in .020 in. to .035 in. Use a .025 in. d

Page 20

27SAFE-T-TIP® NOSE GUARD MAINTENANCESee Figures 42 - 43.Tighten the mounting screw of the nose guard as instructed below. These are specially hardened

Page 21 - MAINTENANCE

28PROBLEM CAUSE SOLUTIONIF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTAC

Page 22

29NOTES

Page 23

3GENERAL SAFETY RULESREAD ALL INSTRUCTIONSBASIC SAFETY PRECAUTIONSn Do not start cutting until you have a clear work area, se-cure footing, and a pla

Page 24

30RYOBI TECHNOLOGIES, INC.1428 Pearman Dairy Road, Anderson, SC 29625Post Office Box 1207, Anderson, SC 29622-1207Phone 1-800-860-4050www.ryobitools.c

Page 25

4GENERAL SAFETY RULESn Avoid body contact with grounded surfaces such as metal pipes and wire fences. There is an increased risk of electric shock if

Page 26

5GENERAL SAFETY RULESKICKBACKSee Figures 1 - 2.WARNING:Kickback may occur when the moving chain contacts an object at the upper portion of the tip of

Page 27

6GENERAL SAFETY RULESUNDERSTANDING YOUR CHAIN SAW SAFETY DEVICESSee Figure 4.SAFE-T-TIP® ANTI-KICKBACK NOSE GUARDThe SAFE-T-TIP® prevents rotationa

Page 28 - PARTS LIST

7 V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power

Page 29

8SYMBOLSSERVICEServicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we su

Page 30

9EXTENSION CORDSWhen using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to h

Commentaires sur ces manuels

Pas de commentaire