Ryobi RPD800-K Spécifications télécharger pdf (Page 4)

Safety

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc, in accordance with these instructions,

taking into account the working conditions and

the work to be performed. Use of the power tool

for operations different from those intended could

result in a hazardous situation.

5) SERVICE

Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

DRILL SAFETY WARNINGS

a) Wear ear protectors when impact drilling. Exposure

to noise can cause hearing loss.

b) Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

c) Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord. Cutting accessory contacting a “live” wire may

make exposed metal parts of the power tool “live” and

could give the operator an electric shock.

d) Hold power tool by insulated gripping surfaces,

when performing an operation where the fastener

may contact hidden wiring or its own cord.

Fasteners contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

e) Wear safety goggles to protect your eyes from flying

particles and splinters.

Additional safety warnings

WARNING

The product is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the product by a

person responsible for their safety.

Children should be supervised to ensure that they

do not play with the product.

a) When working on walls, ceilings or floors, avoid hitting

electrical wiring and gas or water pipes.

b) We recommend the use of a residual current device

with a residual current rating of 30 mA or less.

INTENDED USE

a) Drilling in all types of wood.

b) Drilling in metals: steel, brass, aluminum sheets,

stainless steel and pipe (do not use impact drilling on

these materials).

c) Drilling in masonry: stone and masonry (use impact

drilling), wall tiles (use ordinary drilling first, then impact

drilling).

Do not use this product in any way other than those stated

for intended use.

MAINTENANCE

WARNING

The product should never be connected to a power supply

when you are assembling parts, making adjustments,

cleaning, performing maintenance, or when the product

is not in use. Disconnecting the product will prevent

accidental starting that could cause serious injury.

WARNING

When servicing use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

■ Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to various types of commercial

solvents and may be damaged by their use. Use clean

cloths to remove dirt, carbon dust, etc.

WARNING

Do not at any time let brake ﬂ uids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. They contain chemicals that can

damage, weaken or destroy plastic.

■ Electric tools used on fiberglass material, wallboard,

spackling compounds, or plaster are subject to

accelerated wear and possible premature failure

because the fiberglass chips and grindings are highly

abrasive to bearings, brushes, commutators, etc.

Consequently, we do not recommend using this tool for

extended work on these types of materials. However, if

you do work with any of these materials, it is extremely

important to clean the product using compressed air.

WARNING

Always wear safety goggles or safety glasses with side

shields during power tool operation or when blowing

dust. If operation is dusty, also wear a dust mask.

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Ryobi RPD800-K Spécifications Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Perceuses électriques Ryobi RPD800-K