Page 5
RULES FOR SAFE OPERATION (Continued)
■ To reduce risk of damage to electric plug and cord,
pull by the plug rather than the cord when
disconnecting charger/charging assembly.
■ Make sure cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage
or stress.
■ An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock.
If extension cord must be used, make sure:
a. That pins on plug of extension cord are the same
number, size and shape as those of plug on
charger/charging assembly.
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger/charging assembly as specified
below:
Cord Length (Feet) 25 ft. 50 ft. 100 ft.
Cord Size (AWG) 16 16 16
Note: AWG = American Wire Gage
■ Do not operate charger/charging assembly with
damaged cord or plug. Replace immediately.
■ Do not operate charger/charging assembly if it has
received a sharp blow, been dropped, or otherwise
damaged in any way; take it to a Ryobi Authorized
Service Center.
■ Do not disassemble charger/charging assembly;
take it to a Ryobi Authorized Service Center when
service or repair is required. Incorrect reassembly
may result in a risk of electric shock or fire.
■ To reduce risk of electric shock, unplug charger/
charging assembly from outlet before attempting
any maintenance or cleaning. Turning off controls
will not reduce this risk.
PRECAUTIONS REGARDING THE USE OF
CHARGER/CHARGING ASSEMBLY AND
BATTERY
■ Do not charge battery when temperature is below
50° F (10° C) or above 95° F (35° C).
■ Never attempt to connect two charger/charging
assemblies together.
■ The charger/charging assembly is designed to
operate on standard household electrical power. Do
not attempt to use it on any other voltage.
■ Consecutive charging may cause overheating. If
you need to recharge batteries consecutively, wait
for about 15 minutes to allow charger/charging
assembly to cool.
■ Do not insert foreign matter into the hole for the
battery in charger assembly.
■ Do not charge by means of an engine generator or
DC power source.
■ Do not disassemble the battery.
■ Do not store the tool and battery in locations where
the temperature may reach or exceed 104° F (40°
C), such as outside sheds or metal buildings in
summer.
■ Do not incinerate the battery, even if it is severely
damaged or completely worn out. The battery may
explode in fire.
■ Battery leakage may occur under conditions of
extreme usage or temperature. If liquid comes in
contact with skin, wash quickly with soap and water,
then with lemon juice or vinegar. If liquid gets in your
eyes, wash with water for at least 10 minutes and
seek medical attention immediately.
■ Do not short-circuit the battery.
WARNING:
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.
SAVE THESE INSTRUCTIONS
Look for this symbol to point out important safety precautions.
It means attention!!! Your safety is involved.
(14 pages)
(136 pages)
(24 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels