Ryobi BT3000 Spécifications Page 26

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 42
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 25
Page 26
OPERATION
TO MAKE A BEVEL RIP CUT (Continued)
5. Attach the rip fence over the front and rear rails on the
left side and lock securely. Reset the scale to the blade
if needed.
6. Move the bevel locking lever to the right for Angle mode.
Turn the blade adjustment handle until the bevel indicator
is at the desired angle. Push the bevel locking lever
securely to the left to lock the angle.
7. Position the rip fence the desired distance from the
blade for the cut and lock securely.
8. Place a support (the same height as saw table) behind
the saw for the cut work. See Quick Fold Table in
Accessories on page 38.
9. Use a push stick to move small pieces of wood past the
blade. NEVER PUSH A SMALL PIECE OF WOOD
INTO THE BLADE WITH YOUR HAND.
10. Stand to the side of the wood as it contacts the blade to
reduce the chance of injury should kickback occur.
NEVER STAND DIRECTLY IN THE LINE OF CUT.
11. Make sure the wood is clear of the blade before turning
on the saw.
12. Let the blade build up to full speed before feeding the
workpiece into the blade.
TO MAKE A LARGE PANEL CUT
See Figure 42.
Make sure the saw is properly secured to a work surface so
it will not tip over under the weight of a large panel.
WARNING:
Make sure the blade guard assembly is installed and
working properly to avoid serious personal injury.
1. Raise the locking handle on the rip fence to allow the
rails to move freely.
2. Lift off the sliding miter table assembly by raising the
miter locking clamps to release the grippers.
3. Remove the accessory table by swinging out the lever
and lifting the table up and out.
4. Rotate the front rail clamps (under the front rail) to the
left and slide the front rail to the side where the panel will
rest. Lock the rail clamps after positioning the front rail.
5. Rotate the rear rail clamps (under the rear rail) to the left
and position the rear rail to support the panel. Align the
rear rail with the front rail. Lock the rail clamps after
positioning the rear rail.
6. Place the accessory table onto the rails far enough from
the blade to help support the panel and lock securely.
7. Place the sliding miter table assembly onto the rails and
lock securely. The miter table can be rotated 180 degrees
so the projecting base is at the back of the work surface
so you won't run into it as you feed the panel into the
blade. (Tables can be placed on either side of blade.)
8. Position the rip fence the desired distance from the
blade for the cut and securely lock the handle.
9. Place a support behind the saw for the cut work. See
Wide Table Kit and Quick Fold Table in Accessories on
page 38.
10. Make sure the panel is clear of the blade before turning
on the saw.
11. Let the blade build up to full speed before feeding the
workpiece into the blade.
TO MAKE NON-THROUGH CUTS
Non-through cuts can be made with the grain (ripping) or
across the grain (crosscut). The use of a non-through cut is
essential to cutting grooves, rabbets, and dadoes. This is the
only type cut that is made without the blade guard installed.
Make sure the blade guard assembly is reinstalled upon
completion of this type of cut. Read the appropriate section
which describes the type of cut in addition to this section on
non-through or dado cuts. For example, if your non-through
cut is a straight cross cut, read and understand the section on
straight cross cuts before proceeding.
SLIDING MITER
TABLE ASSEMBLY
Figure 42: Large Panel Set-up
ACCESSORY
TABLE
RAIL
CLAMP
ACCESSORY
TABLE
TO MAKE A COMPOUND MITER CUT
This cut is made with both the miter fence and the blade
angled. Set the miter fence and the blade angle with the
procedures given earlier.
The miter fence must be on the left side of the blade. It is
highly recommended that you test the cut with a piece of
scrap wood. Become thoroughly familiar with bevel cross
cuts and miter cuts before attempting to perform a com-
pound miter cut.
MITER
LOCKING CLAMPS
Vue de la page 25
1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 41 42

Commentaires sur ces manuels

Pas de commentaire