Your new cordless chain saw has been engineered and manufactured to Ryobi's high standard for dependability, easeof operation, and operator safe
10Motor 18 Volt, DCBar Length 10 in. (254 mm)Replacement Bar Part No. 671256002 or 671667002Replacement Chain Part No. 6958301 or 690583002Net Weight
11Fig. 5CHAIN OIL TANK CAPREAR HANDLEFRONT HANDLEBARCHAINSAFE-T-TIP®BATTERY PACKHEX KEYHEX KEYSTORAGE AREAHAND GUARDTRIGGER LOCKBUTTONTRIGGERFEATURESS
12GLOSSARY OF TERMSFront HandleThe support handle located at or toward the front ofthe chain saw.Front Handle GuardA structural barrier between the fr
13BATTERY PACK AND CHARGERLED FUNCTION OF CHARGERSee Figure 6.LED WILL BE ON TO INDICATE STATUS OFCHARGER AND BATTERY PACK: Red LED on = Fast chargin
14TO INSTALL BATTERY PACKSee Figure 7.1. Place the battery pack in your chain saw. Alignraised rib on battery pack with groove in chainsaw’s battery p
15Fig. 9TRIGGER LOCKBUTTONTRIGGER WARNING:Keep body to the left of the chain line. Neverstraddle the saw or chain, or lean over past thechain line.S
163. Maintain a proper grip on the saw whenever theunit is running. The fingers should encircle thehandle and the thumb is wrapped under the handle-ba
17Fig. 13PROPER CUTTING STANCESee Figure 13. Weight should be balanced with both feet on solidground. Keep left arm with elbow locked in a "str
18 WARNING:If the tree starts to fall in the wrong direction, orif the saw gets caught or hung up during the fall,leave the saw and save yourself! F
19 Felling Backcut. The backcut is always madelevel and horizontal, and at a minimum of 2 inches(5 cm) above the horizontal cut of the notch. SeeFigu
2 Table of Contents / Introduction ...
20LOADFINISHING CUT1ST CUT1/3 DIALOG SUPPORTED AT ONE END:LOG SUPPORTED AT BOTH ENDS: FINISHING CUT1ST CUT 1/3 DIALOADFig. 20OPERATIONBUCKING LOGS UND
21TYPES OF CUTTING USEDSee Figure 21.OVERBUCKINGBegin on the top side of the log with the bottom of thesaw against the log; exert light pressure downw
22PRUNINGSee Figure 23.Pruning is trimming limbs from a live tree. Work slowly, keeping both hands on the chain sawwith a firm grip. Always make sure
23ASSEMBLING BAR AND CHAINSee Figures 25, 26, 27, 28 and 29. WARNING:The safety instructions in this section are toprotect the user from serious pers
24Fig. 27CHAINTENSIONINGSCREW7. Replace the chain cover, washer and chain coverscrew. Tighten the chain cover screw finger tightonly. The bar must be
25CHAIN TENSIONSee Figures 30 and 31.1. Stop the engine before setting the chain tension.Make sure the guide bar screw is loosened to fingertight, tur
26CHAIN MAINTENANCESee Figures 32 and 33.Fig. 34Fig. 33CHECK FOR WEAR ORDAMAGEUse only low-kickback chain on this saw. This fast-cutting chain will p
27 WARNING:Improper chain sharpening increases thepotential of kickback.5. Put a few firm strokes on every tooth. File all lefthand cutters in one di
28Use a Flat File and a Depth Gauge Jointer to lower allgauges uniformly. Depth gauge jointers are available in.020 in. to .035 in. (0.5 mm to 0.9 mm)
29SAFE-T-TIP® NOSE GUARD MAINTE-NANCESee Figures 42 and 43.Tighten the mounting screw of the nose guard asinstructed below. These are specially harden
3READ ALL INSTRUCTIONSBASIC SAFETY PRECAUTIONS Do not operate a chain saw with one hand! Use afirm grip with thumbs and fingers encircling thechain s
30BATTERIESThe battery pack for your chain saw is equipped withnickel-cadmium rechargeable batteries. Length ofservice from each charging will depend
31RECOMMENDED BAR AND CHAIN COMBINATIONSBar Part Number - 10 in. (254 mm) 671256002 or 671667002Chain Part Number 6958301 or 690583002BAR AND CHAIN CO
32NOTES
33NOTES
983000-35310-04RYOBI TECHNOLOGIES INC.1428 Pearman Dairy Road Anderson, SC 29625Post Office Box 1207 Anderson, SC 29622www.ryobitools.com1-800-525-257
4KICKBACKSee Figures 1 and 2. WARNING: Kickback may occur when the movingchain contacts an object at the upper portion of thetip of the guide bar or
5IMPORTANT SAFETY INSTRUCTIONSPULLPUSHFig. 3 Push and Pull - This reaction force is alwaysopposite to the direction the chain is moving wherewood con
6UNDERSTANDING YOUR CHAIN SAWSAFETY DEVICESSee Figure 4.SAFE-T-TIP® Anti-Kickback Nose GuardThe SAFE-T-TIP® prevents kickback from happening,because i
7b. That extension cord is properly wired and ingood electrical condition; andc. That wire size is large enough for AC ampererating of charger as spec
8Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning.Proper interpretation of these symbols w
9Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning.Proper interpretation of these symbols w
Commentaires sur ces manuels