Ryobi BS1001SV Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Scies à moteur Ryobi BS1001SV. Ryobi BS1001SV User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 28
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
OPERATOR'S MANUAL
10 in. BAND SAW
BS1001SV
SAVE THIS MANUAL FOR FUTURE REFERENCE
Your new Band Saw has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation,
and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for buying a Ryobi product.
Vue de la page 0
1 2 3 4 5 6 ... 27 28

Résumé du contenu

Page 1 - OPERATOR'S MANUAL

OPERATOR'S MANUAL10 in. BAND SAWBS1001SVSAVE THIS MANUAL FOR FUTURE REFERENCEYour new Band Saw has been engineered and manufactured to Ryobi&apos

Page 2 - INTRODUCTION

Page 10FEATURESLED LIGHTINGYour band saw comes equipped with LED lighting that lights the work area for safer, more accurate cuts.MITER GAUGEThis gaug

Page 3 - GENERAL SAFETY RULES

Page 11Fig. 3The following tools (not included) are needed for assembly and alignment:TOOLS NEEDEDPHILLIPS SCREWDRIVER10 mm WRENCHThe following items

Page 4 - SPECIFIC SAFETY RULES

Page 12LOOSE PARTS LISTLEG BRACE (LONG) FEETLEGLEG BRACE (SHORT)TOP BRACE (RIGHT)TOP BRACE(LEFT)Fig. 5TOP BRACE(FRONT)TOP BRACE(BACK)LEG BRACE (LONG)L

Page 5

Page 13ASSEMBLYUNPACKINGThis product requires assembly.n Carefully remove the tool and any accessories from the box. Place it on a level work surface

Page 6 - SAVE THESE INSTRUCTIONS

Page 14ASSEMBLYn Use the same steps to install the lower braces. Tighten all hex nuts with a wrench.n Place a carriage bolt in each of the four hole

Page 7 - GLOSSARY OF TERMS

Page 15ASSEMBLYTO SQUARE THE SAW TABLE TO THE BLADESee Figure 11.n Turn the blade guide lock knob counterclockwise to unlock the blade guide a

Page 8 - ELECTRICAL

Page 16ASSEMBLYBLADE TENSION KNOBTO INCREASETENSIONTO DECREASETENSIONTO ADJUST BLADE TENSIONSee Figures 13 - 14.n Unplug the saw and remove the switc

Page 9

Page 17OPERATION WARNING:Do not allow familiarity with tools to make you care-less. Remember that a careless fraction of a second issufficien

Page 10 - FEATURES

Page 18OPERATIONAVOIDING INJURYn Make sure saw is level and does not rock. Saw should always be on a firm, level surface with plenty of room for hand

Page 11 - LOOSE PARTS LIST

Page 19OPERATIONTO EXTEND THE SAW TABLESee Figure 17.The saw table can be extended to increase the work surface. To lengthen the saw table:n Loosen t

Page 12

Page 2n Introduction ...

Page 13 - ASSEMBLY

Page 20OPERATIONUSING THE RIP FENCESee Figure 20.n Unplug the saw.n From either side of the saw blade, slide the rip fence onto the saw table. Check

Page 14

Page 21ADJUSTMENTSBLADEGUIDEASSEMBLYSAWBLADEUPPERWHEELBLADE TENSION KNOBRAPIDSET™ BLADE TENSION LEVERLOWER WHEELBLADE GUIDE ASSEMBLYBLADE GUIDE KNOBBL

Page 15

Page 22ADJUSTMENTS WARNING:To avoid personal injury, maintain proper adjustment of blade tension, blade guides, and thrust bearings.n To check tension

Page 16

Page 23ADJUSTMENTSMITER GAUGE INDICATORSCREWTo Adjust Blade Guide Support:n Remove the blade guard by removing the two phillips screws that secure

Page 17 - OPERATION

Page 24MAINTENANCEWARNING:When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or ca

Page 18

Page 25MAINTENANCEBRUSHESSee Figure 28. WARNING:To prevent accidental starting that could cause possible serious personal injury, turn off the s

Page 19

Page 26TROUBLESHOOTINGPROBLEM CAUSE SOLUTIONMotor will not run.

Page 21

Page 28983000-269 8-04RYOBI TECHNOLOGIES, INC.1428 Pearman Dairy Road, Anderson SC 29625Post Office Box 1207, Anderson SC 29622-1207Phone 1-800-525-2

Page 22

Page 3GENERAL SAFETY RULESn DO NOT OVERREACH. Keep proper footing and balance at all times.n MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for

Page 23

Page 4n BE SURE THE BLADE PATH IS FREE OF NAILS. Inspect for and remove nails from lumber before cutting.n AVOID AWKWARD OPERATIONS AND HANDPOSITI

Page 24 - MAINTENANCE

Page 5SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-tion of these symbol

Page 25

Page 6SYMBOLSSERVICEServicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service

Page 26 - TROUBLESHOOTING

Page 7GLOSSARY OF TERMSResawA cutting operation to reduce the thickness of the workpiece to make thinner pieces.ResinA sticky, sap-based substance tha

Page 27

Page 8ELECTRICALFig. 1 GROUNDING PINCOVER OF GROUNDED OUTLET BOXEXTENSION CORDSUse only 3-wire extension cords that have 3-prong ground-ing plugs and

Page 28

Page 9Fig. 2FEATURESDUSTEXHAUSTPORTTRACKINGKNOBSCALEINDICATORBLADE GUIDE LOCK KNOBSCALEBEVELADJUSTMENTKNOBRAPIDSET™ BLADE TENSION LEVERSAW BLADESWITCH

Commentaires sur ces manuels

Pas de commentaire