Ryobi BTS20R-1 Manuel d'utilisateur

OPERATOR’S MANUAL10 in. (254 mm) TABLE SAWBTS20R-1SAVE THIS MANUAL FOR FUTURE REFERENCEYour table saw has been engineered and manufactured to our high

Page 10FEATURESInput ... 120 V, 60 Hz, AC only, 15 ampsNo Load Speed ...4,800 r/min. (

Page 11FEATURESKNOW YOUR TABLE SAWSee Figure 2.The safe use of this product requires an understanding of the information on the tool and in this opera

Page 12Fig. 3SWITCH KEYFEATURESOPERATING COMPONENTSThe upper portion of the blade projects up through the table, surrounded by an insert call

Page 13PHILLIPS SCREWDRIVERFRAMING SQUAREWRENCH (2) 1/2 in., 8 mm Fig. 4TOOLS NEEDEDThe following tools (not included) are needed for making adjustmen

Page 14ASSEMBLYUNPACKINGThis product requires assembly. Carefully lift saw from the carton and place it on a level work surface. NOTE: This tool is

Page 15ASSEMBLYASSEMBLING WHEELSSee Figures 6 - 7.  Remove the following hardware from the bag: 2 wheels 2 washers 2 shoulder bolts Plac

Page 16ASSEMBLYOPENING THE LEG STANDSee Figure 9.NOTE: You can also refer to the blue label on the right-hand side of the table saw for setup procedur

Page 17REMOVING/REPLACING THE THROAT PLATESee Figure 10. Unplug the saw. Lower the blade by turning the height adjusting handwheel counterclockwi

Page 18TO INSTALL BLADE GUARD ASSEMBLYSee Figure 13. Lower the blade by turning the height adjusting handwheel clockwise.� Using the small wrench,

Page 19OPERATION Using the wrong blade for the type of cut Not following correct operating procedures Misusing the saw Failing to use the anti

Page 2TABLE OF CONTENTS Introduction ...

Page 20OPERATIONFig. 17BEVEL RIP CUT RIP CUT CROSS CUT MITER CUT COMPOUND (BEVEL) MITER CUT BEVEL CROSS CUT 126453TYPES OF CUTSSee Figure 17.There are

Page 21OPERATIONTO CHANGE BLADE DEPTHSee Figure 18.The blade depth should be set so that the outer points of the blade are higher than the workpiece b

Page 22OPERATIONTO USE THE RIP FENCESee Figure 21. Place the front lip on the front rail and push slightly toward the rear of the unit. Lower the

Page 23OPERATIONHEELING (PARALLELING) THE BLADE TO THE MITER GAUGE GROOVESee Figures 25 - 27 .WARNING:The blade must parallel the miter gauge slot so

Page 24OPERATIONMAKING CUTSThe blade provided with your saw is a high-quality combina-tion blade suitable for ripping and crosscut operations. WARNING

Page 25+-OPERATIONMAKING A MITER CUTSee Figure 30. It is recommended you make test cuts on scrap wood.WARNING:Make sure the blade guard assembly

Page 2615301530OPERATIONMAKING A BEVEL CROSS CUTSee Figure 32.It is recommended that you place the piece to be saved on the left side of the blade and

Page 27OPERATIONMAKING A COMPOUND MITER CUTIt is recommended that you place the piece to be saved on the left side of the blade and that you make a te

Page 28OPERATIONWARNING: Never feed wood with your hands when making any non-through cut such as rabbets or dadoes.WARNING: When making a non-through

Page 29ADJUSTMENTSBLADE GUARDTHROAT PLATEBEVEL LOCKING LEVERBEVEL HANDWHEELFig. 35TO ANGLE BLADE, PUSH BEVEL LOCKING LEVER RIGHT AND ROTATE BEVEL HAND

Page 3 WARNING:Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serio

Page 30ADJUSTMENTSTO SET BLADE INDICATOR AND BEVEL STOPS AT 0° OR 45° (SQUARING THE BLADE) See Figure 38.The angle settings of your saw have been set

Page 31ADJUSTMENTSTO CHECK THE ALIGNMENT OF THE RIP FENCE TO THE BLADESee Figure 40. Raise the locking handle to permit the rip fence to be move

Page 321. Blade is out of balance. 2. Blade is warped or damaged. 3. Saw is not mounted securely to a level work surface. 1. Rip fence not mounted

Page 33NOTESNOTES

Page 34987000-0136-28-06 (REV:00)ONE WORLD TECHNOLOGIES, INC.1428 Pearman Dairy Road, Anderson, SC 29625Phone 1-800-525-2579www.ryobitools.comOPERATOR

Page 4GENERAL SAFETY RULES work or around or over the blade while blade is rotating. Do not attempt to remove cut material when blade is movin

Page 5SPECIFIC SAFETY RULES WARNING:Some dust created by power sanding, sawing, grinding, drilling, and other construction activities con

Page 6SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Properinterpretation

Page 7SYMBOLSThe following signal words and meanings are intended to explain the levels of risk associated with this product.DANGER:Indicates an immin

Page 8ELECTRICALSPEED AND WIRINGThe no-load speed of this tool is approximately 4,800 rpm. This speed is not constant and decreases un

Page 9GLOSSARY OF TERMSNon-Through CutsAny cutting operation where the blade does not extend completely through the thickness of the workpiece