Ryobi CR120L Manuel d'utilisateur Page 7

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 28
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 6
7 – English
WARNING:
Do not allow familiarity with products to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear eye protection marked to comply with
ANSI Z87.1. Failure to do so could result in objects
being thrown into your eyes resulting in possible seri-
ous injury.
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.
APPLICATIONS
You may use this product for the purposes listed below:
Cutting all types of wood and wood products
Cutting thin sheet metal
Cutting plastics and laminates
Cutting drywall
For complete charging instructions, refer to the Operator’s
Manual for the battery packs and chargers listed in the
General Safety Rules.
BATTERY PROTECTION FEATURES
Ryobi lithium-ion batteries are designed with features that
protect the lithium-ion cells and maximize battery life.
If the tool stops during use, release the trigger to reset and
resume operation. If the tool still does not work, the battery
needs to be recharged.
TO INSTALL BATTERY PACK
See Figure 2, page 10.
WARNING:
Always remove battery pack from the product when you
are assembling parts, making adjustments, cleaning, or
when not in use. Removing battery pack will prevent acci-
dental starting that could cause serious personal injury.
Insert the battery pack into the product as shown.
Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured before
beginning operation.
TO REMOVE BATTERY PACK
See Figure 2, page 10.
Depress the latches on each side of the battery pack.
Remove the battery pack from the tool.
WARNING:
Battery products are always in operating condition.
Therefore, the switch should always be locked when not
in use or carrying at your side.
TO INSTALL SAW BLADE
See Figure 3, page 10.
Remove the battery pack.
Push down and hold the blade clamp lock/release
lever.
Insert the saw blade into the blade clamp as far as it will
go. The cutting edge of the blade should face the blade
clamp lock/release lever.
Release the blade clamp lock/release lever. Make sure
the blade is secure.
Replace the battery pack.
NOTE: Ryobi recommends T-shank style blades; If U-shank
style blades are used, they should be high-quality hardened
steel.
LOCK-OUT LEVER
See Figure 4, page 10.
Your hybrid saw is equipped with a lock-out lever to help
prevent accidental starting of the trigger.
To activate the trigger:
Tilt the lock-out lever toward the tool.
Squeeze the trigger firmly against the tool body.
GENERAL CUTTING
See Figure 5, page 10.
Hold the hybrid saw firmly in front of and clearly away from
you. Make sure saw blade is clear of any foreign material.
Be sure material to be cut is held firmly. Small work pieces
should be securely clamped in a vise or with clamps to the
work bench or table. Mark the line of cut clearly. Push the
lock-out lever forward and squeeze the trigger to start the
cutting action. Place the base assembly against the work, then
move the blade into the work. Do not force. Use only enough
pressure to keep the saw cutting. Let the blade and saw do
the work. Use of excessive pressure that causes bending or
twisting of the blade may result in broken blades.
SCROLL CUTTING
See Figure 6, page 10.
Scroll cuts can be made with the hybrid saw by guiding the
direction of the cut with applied pressure on the handle as
shown.
OPERATION
Vue de la page 6
1 2 3 4 5 6 7 8 9 10 11 12 ... 27 28

Commentaires sur ces manuels

Pas de commentaire