Ryobi CSB125 Manuel d'utilisateur télécharger pdf (Page 4)

4 - English

CIRCULAR SAW SAFETY WARNINGS

 Do not use dull or damaged blades. Unsharpened

or improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback.

 Blade depth and bevel adjusting locking levers must be

tight and secure before making cut. If blade adjustment

shifts while cutting, it may cause binding and kickback.

 Use extra caution when sawing into existing walls or

other blind areas. The protruding blade may cut objects

that can cause kickback.

LOWER GUARD FUNCTION

 Check lower guard for proper closing before each

use. Do not operate the saw if lower guard does not

move freely and close instantly. Never clamp or tie the

lower guard into the open position. If saw is accidentally

dropped, lower guard may be bent. Raise the lower guard

with the retracting handle and make sure it moves freely

and does not touch the blade or any other part, in all

angles and depths of cut.

 Check the operation of the lower guard spring. If the

guard and the spring are not operating properly, they

must be serviced before use. Lower guard may operate

sluggishly due to damaged parts, gummy deposits, or a

build-up of debris.

 Lower guard should be retracted manually only for

special cuts such as “plunge cuts” and “compound

cuts.” Raise lower guard by retracting handle and as

soon as blade enters the material, the lower guard

must be released. For all other sawing, the lower guard

should operate automatically.

 Always observe that the lower guard is covering the

blade before placing saw down on bench or floor. An

unprotected, coasting blade will cause the saw to walk

backwards, cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch is released.

ADDITIONAL SAFETY WARNINGS



Use clamps or other practical way to secure and

support the workpiece to a stable platform. Holding the

work by hand or against your body is unstable and may

lead to loss of control.

 Know your power tool. Read operator’s manual

carefully. Learn its applications and limitations, as well

as the specific potential hazards related to this tool.

Following this rule will reduce the risk of electric shock,

fire, or serious injury.

 Always wear eye protection with side shields marked

to comply with ANSI Z87.1. Failure to do so could

result in objects being thrown into your eyes, resulting in

possible serious injury.

 Protect your lungs. Wear a face or dust mask if the

operation is dusty. Following this rule will reduce the

risk of serious personal injury.

 Protect your hearing. Wear hearing protection during

extended periods of operation. Following this rule will

reduce the risk of serious personal injury.

 Inspect tool cords periodically and, if damaged, have

repaired at your nearest authorized service center.

Constantly stay aware of cord location. Following this

rule will reduce the risk of electric shock or fire.

 Check damaged parts. Before further use of the

tool, a guard or other part that is damaged should

be carefully checked to determine that it will operate

properly and perform its intended function. Check for

alignment of moving parts, binding of moving parts,

breakage of parts, mounting, and any other conditions

that may affect its operation. A guard or other part that

is damaged should be properly repaired or replaced

by an authorized service center. Following this rule will

reduce the risk of shock, fire, or serious injury.

 Make sure your extension cord is in good condition.

When using an extension cord, be sure to use one

heavy enough to carry the current your product

will draw. A wire gauge size (A.W.G.) of at least

12 is recommended for an extension cord 50 feet

or less in length. A cord exceeding 100 feet is not

recommended. If in doubt, use the next heavier gauge.

The smaller the gauge number, the heavier the cord.

An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating.

 Inspect for and remove all nails from lumber before

using this tool. Following this rule will reduce the risk of

serious personal injury.

If the power supply cord is damaged, it must be

replaced only by the manufacturer or by an authorized

service center to avoid risk.

 Save these instructions. Refer to them frequently and

use them to instruct others who may use this tool. If you

loan someone this tool, loan them these instructions also.

1 2 3 4 5 6 7 8 9 ... 47 48

Commentaires sur ces manuels

Pas de commentaire

Ryobi CSB125 Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à moteur Ryobi CSB125