Ryobi CSB134 Manuel d'utilisateur télécharger pdf (Page 11)

11 - English

OPERATION

DANGER:

When sawing through work, lower blade guard does not

cover blade on the underside of work. Since blade is

exposed on underside of work, keep hands and fingers

away from cutting area. Any part of your body coming

in contact with moving blade will result in serious injury.

WARNING:

Never tie the lower blade guard in a raised position.

Leaving the blade exposed could lead to serious injury.

CAUTION:

Never use saw when guard is not operating correctly.

Check the guard for correct operation before each use.

The guard is operating correctly when it moves freely and

readily returns to the closed position. If you drop the saw,

check the lower blade guard and bumper for damage at

all depth settings before reuse.

If at any time the lower blade guard does not snap closed,

unplug the saw from the power supply. Exercise the lower

guard by moving it rapidly back and forth from the full open

position to the closed position several times. Normally this

will restore the guard to its normal operating condition. If

it does not correct a slow or sluggish closing lower guard,

do not use the saw. Take it to an authorized factory service

center for repair.

STARTING/STOPPING THE SAW

See Figure 10, page 18.

To start the saw: Depress the switch.

Always let the blade reach full speed, then guide the saw

into the workpiece.

WARNING:

The blade coming in contact with the workpiece before

it reaches full speed could cause the saw to “kickback”

towards you resulting in serious injury.

To stop the saw: Release the switch.

After you release the switch, allow the blade to come to a

complete stop. Do not remove the saw from the workpiece

while the blade is moving.

ADJUSTING BLADE DEPTH

See Figure 11, page 18.

Always keep correct blade depth setting. Less than a full tooth

of the blade teeth should be visible below the workpiece.

More blade depth will increase the chance of kickback and

cause the cut to be rough. For more depth of cut accuracy,

a scale is located on the upper blade guard.

To adjust the blade depth:

Unplug the saw.

Pull depth lock lever upward to release. The depth lock

lever is located between the guard and handle of the saw.

Determine the desired depth of cut.

Locate depth of cut scale and index point on back of

upper blade guard.

Hold base flat against the workpiece and raise or lower

saw until the index point (or reference mark) on bracket

aligns with notch on blade guard.

Push down on the depth lock lever to lock the lever in

place and secure the position.

USING THE LASER GUIDE

See Figure 12, page 18.

WARNING:

Do not stare into the laser beam or turn the laser on when

the tool is not in use. Failure to heed this warning could

result in possible serious personal injury.

The laser unit comes from the factory already installed and

aligned. If the laser becomes misaligned after time refer to

the “ADJUSTMENTS” section.

NOTE: Make a trial cut on a piece of scrap to ensure laser

is aligned. Adjusting the laser may be necessary.

 Mark the line to be cut on the workpiece.

 Adjust the depth and angle of the cut as needed and lock

the depth and bevel settings.

 Connect the saw to a power supply.

 Depress the switch to start the motor. The laser guide will

turn on when the switch is depressed and turn off when

the switch is released.

NOTE: Do not touch the blade to the workpiece until the

saw has reached maximum speed.

 Slowly push the saw forward into the workpiece.

NOTE: Keep the laser beam on the marked line on the

workpiece for precision cutting.

 Once the cut is complete, allow the saw to come to a

complete stop. The laser will turn off when the switch is

released.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

Ryobi CSB134 Manuel d'utilisateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à moteur Ryobi CSB134