Ryobi CSB134 Manuel d'utilisateur télécharger pdf (Page 12)

12 - English

OPERATING THE SAW

See Figures 13 - 15, page 19.

It is important to understand the correct method for operat-

ing the saw. Refer to the figures in this section to learn the

correct and incorrect ways for handling the saw.

WARNING:

To make sawing easier and safer, always maintain proper

control of the saw, by holding the saw with both hands.

Loss of control could cause an accident resulting in pos-

sible serious injury.

DANGER:

When lifting the saw from the workpiece, the blade is

exposed on the underside of the saw until the lower blade

guard closes. Make sure the lower blade guard is closed

before setting the saw down.

WARNING:

Use clamps or other practical way to secure and

support the workpiece to a stable platform. Holding

the work by hand or against your body is unstable and

can lead to loss of control which could cause possible

serious injury.

To make the best possible cut:

Hold the saw firmly with both hands.

Avoid placing your hand on the workpiece while making

a cut.

Support the workpiece so that the cut is always on your

right.

Support the workpiece near the cut.

Clamp the workpiece securely so that the workpiece will

not move during the cut.

Avoid placing the saw on the part of the workpiece that

will fall off when the cut is made.

Place the workpiece with the “good” side down.

Draw a guideline along the desired line of cut before

beginning your cut.

Keep the cord away from the cutting area. Always place

the cord to prevent it from hanging up on the workpiece

while making a cut.

DANGER:

If the cord hangs up on the workpiece during a cut,

release the switch immediately and allow the blade to

come to a complete stop. Unplug the saw and reposition

the cord to prevent it from hanging up again.

OPERATION

DANGER:

Using a saw with a damaged cord could result in serious

injury or death. If the cord has been damaged, have it

replaced before using the saw again.

LENGTH OF CUT SCALE

See Figure 16, page 19.

The saw is equipped with a length of cut scale on its base.

It is parallel with the saw blade and can be used to measure

the distance into the material the blade cuts.

NOTE: Six inches is the maximum length of cut that you can

measure. Also, it is accurate only when the depth of cut is

set at full maximum depth.

CROSS CUTTING/RIP CUTTING

See Figure 17, page 19.

When making a cross cut or rip cut, align the line of cut with

the outer blade guide notch on the base as shown in the figure.

Since blade thicknesses vary, always make a trial cut in scrap

material along a guideline to determine how much, if any,

you must offset the guideline to produce an accurate cut.

NOTE: The distance from the line of cut to the guideline is

the amount you should offset the guide.

TO RIP CUT WITHOUT EDGE GUIDE

See Figure 18, page 19.

Use a guide when making long or wide rip cuts with the saw.

NOTE: You may also use an edge guide to make rip cuts. Refer

to “OPTIONAL EDGE GUIDE” section later in this manual.

Secure the workpiece.

Clamp a straight edge to the workpiece using

C-clamps.

Saw along the straight edge to achieve a straight rip cut.

NOTE: Do not bind the blade in the cut.

BEVEL CUTTING

See Figures 19 - 21, page 19.

To make the best possible cut, follow these helpful hints.

Align the line of cut with the inner blade guide notch on

the base when making 45° bevel cuts.

Make a trial cut in scrap material along a guideline to

determine how much you should offset the guideline on

the cutting material.

Adjust the angle of the cut to any desired setting between

zero and 51.5°. Refer to “TO ADJUST BEVEL SETTING”

section.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

Ryobi CSB134 Manuel d'utilisateur Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à moteur Ryobi CSB134