Ryobi CSB134 Manuel d'utilisateur télécharger pdf (Page 14)

14 - English

WARNING:

Never tie the lower blade guard in a raised position.

Leaving the blade exposed could lead to serious injury.

0° BEVEL STOP

See Figure 25, page 20.

The saw has a 0° bevel stop that has been factory adjusted

to assure 0° angle of the saw blade when making 0° cuts.

To check 0° bevel stop:

Unplug the saw.

Place the saw in an upside down position on a work-

bench.

Check the squareness of the saw blade plate to the base

of the saw using a combination square.

To adjust 0° bevel stop:

Unplug the circular saw.

Loosen bevel adjustment knob.

Loosen hex nut securing adjusting screw.

Turn adjusting screw and adjust base until square with

saw blade.

Tighten hex nut and bevel adjustment knob securely.

WARNING:

Attempting a bevel cut without having the bevel

adjustment knob securely tightened can result in seri-

ous injury.

CHECKING/ADJUSTING THE LASER

ALIGNMENT

See Figure 26, page 21.

DANGER:

Laser radiation. Avoid direct eye contact with light

source.

WARNING:

Use of controls or adjustments or performance of

procedures other than those specified herein can result

in hazardous radiation exposure.

 Unplug the saw.

 REMOVE the blade before adjusting the laser.

 Clamp a straight edge to the straight side of a workpiece.

 Square the long edge of the saw base against the straight

edge.

 With a pencil, mark the workpiece in front of the far right

notch on the saw’s base.

 Slide the saw along the straight edge and mark the notch

10 - 12 in. from the first mark. Draw a guideline to connect

the two marks.

 Slide the saw back to the starting position so that the

entire guideline is visible.

 Connect the saw to a power supply.

 Depress and hold the switch until the laser turns on.

NOTE: The laser will activate without the saw motor run-

ning.

 The laser beam should align with the notch in the saw

base and the guideline you drew on the workpiece.

 If the laser beam is out of adjustment, use a 1/8 in. flat

head screwdriver to turn the laser adjusting screw until

the beam aligns with the guideline.

 Slowly turn the screw counterclockwise to adjust the laser

to the left, or clockwise to adjust the laser to the right.

ADJUSTING THE DEPTH LOCK LEVER

See Figure 27, page 21.

Over time, due to wear, the depth lock lever may move from

its original setting. If the lever prematurely contacts any part

of the saw during tightening and loosening, adjust the lever

by following these steps:

Unplug the saw.

Pull depth lock lever upward to release.

Pull saw base down to the minimum depth of cut position,

then push the depth lock lever down to secure.

Insert a flathead screwdriver into the space between the

lock nut and the E-ring. Remove the E-ring.

Note the position of the lever on the nut. Slide the depth

lock lever off the lock nut.

The lock nut has six flat sides. Rotate the depth lock lever

one “flat” counter clockwise around the nut. Then slide it

back into place.

Push the E-ring back into the groove on the lock nut until

it snaps into place. Take care that the E-ring does not pop

off the lock nut.

Loosen the depth lock lever and return the base to the

full depth of cut position and lock the depth setting by

pushing downward on the depth lock lever. The base

should be locked securely in position when locked and

be free to move when released.

ADJUSTMENTS

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 51 52

Commentaires sur ces manuels

Pas de commentaire

Ryobi CSB134 Manuel d'utilisateur Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à moteur Ryobi CSB134