Ryobi TS1342 Manuel d'utilisateur

SAVE THIS MANUAL FOR FUTURE REFERENCEOPERATOR’S MANUAL10 in. Compound Miter SawTS1342 - Double InsulatedYour miter saw has been engineered and manufac

10FEATURESPRODUCT SPECIFICATIONSBlade Arbor ... 5/8 in.Blade Diameter ...

11FEATURESKNOW YOUR COMPOUND MITER SAWSee Figure 1.The safe use of this product requires an understanding of the information on the tool and in this o

12FEATURESPOSITIVE STOPS ON MITER TABLEPositive stops have been provided at 0°, 15°, 22-1/2°, 30°, and 45°. The 22-1/2° and 45° positive stops have be

13LOOSE PARTSWARNING:The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.The following items a

14ASSEMBLYFig. 7MOUNTING SURFACE BASETRACE HOLES AT THESE LOCATIONS FOR HOLE PATTERNTRACE HOLES AT THESE LOCATIONS FOR HOLE PATTERNWARNING:Do not sta

15ASSEMBLYFig. 8Fig. 10TO LOOSENMITER LOCK HANDLETO TIGHTENDUST BAGEXHAUST PORTBASEWORK CLAMPMITER LOCK HANDLESee Figure 8.To install the miter lock h

16ASSEMBLYTO INSTALL / REPLACE THE BLADESee Figures 11 - 12.WARNING:A 10 in. blade is the maximum blade capacity of the saw. Never use a blade that is

17ASSEMBLYFig. 13WARNING:Make sure the spindle lock button is not engaged before reconnecting saw into power source. Never engage sp

18ASSEMBLYSQUARING THE SAW BLADE TO THE FENCESee Figures 16 - 20 Unplug the saw. Pull the saw arm all the way down and engage the lock pin to hold

19ASSEMBLYFig. 20SQUARING THE BLADE TO THE MITER TABLESee Figures 21 - 23. Unplug the saw. Pull the saw arm all the way down and engage the lock p

2 Introduction ...

20OPERATIONWARNING:Do not allow familiarity with tools to make you care-less. Remember that a careless fraction of a second is sufficient to

21Fig. 25OPERATION Rotate the control arm until the pointer aligns with the desired angle on the miter scale. Release the miter lock plate. NOTE

22OPERATION Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece w

230OPERATION Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece

24OPERATION4 PITCH OF SIDENUMBER OF SIDES0°6M- 45.00°B- 0.00°5°10°15°20°25°30°35°40°45°50°55°60°65°70°75°80°85°90°578 910M- 36.00°B- 0.00°M- 3

25OPERATIONWhen setting the bevel and miter angles for compound miters, remember that the settings are interdependent; changing one angle changes th

26OPERATIONWARNING: To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material against the

27ADJUSTMENTSWARNING:Before performing any adjustment, make sure the tool is unplugged from the power supply. Failure to heed this warning could resul

28MAINTENANCEWARNING:When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause p

29NOTES

3GENERAL SAFETY RULESWARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fir

• SERVICENow that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service

4GENERAL SAFETY RULES INSPECT TOOL CORDS PERIODICALLY. If damaged, have repaired by a qualified service technician at an authorized service fa

5SPECIFIC SAFETY RULES NEVER reach behind, under, or within three inches of the blade and its cutting path with hands and fingers for any reason.

6SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Properinterpretation of t

7SYMBOLSSERVICEServicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we su

8EXTENSION CORDSWhen using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to h

9GLOSSARY OF TERMSNon-Through CutsAny cutting operation where the blade does not extend completely through the thickness of the workpiece.Push