Ryobi TS1552LA Manuel d'utilisateur

SAVE THIS MANUAL FOR FUTURE REFERENCEYour miter saw has been engineered and manufactured to our high standard for dependability, ease of operation,

10FEATURESFig. 1PRODUCT SPECIFICATIONSBlade Arbor ... 5/8 in.Blade Inner Washer ...

11FEATURESFig. 3KNOW YOUR COMPOUND MITER SAWSee Figure 1.The safe use of this product requires an understanding of the information on the tool and in

12FEATURESPOSITIVE STOPS ON MITER TABLEPositive stops have been provided at 0°, 15°, 22-1/2°, 30°, and 45°. The 22-1/2° and 45° positive stops have be

13LOOSE PARTS LISTFig. 6WARNING:The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.The follow

14ASSEMBLYtrace hoLes at these LocatIons For hoLe patternWARNING:Do not connect to power supply until assembly is complete. Failure to com

15ASSEMBLYMITER LOCK HANDLESee Figure 8.To install the miter lock handle, place the threaded stud on the end of the miter lock handle into the threade

16ASSEMBLYREAR BRACKETSee Figure 12.WARNING:A rear bracket is included with this miter saw to prevent tipping if the saw arm is released suddenly. Do

17ASSEMBLYFig. 15stop bLocksMaLL wIng screwtabLe eXtensIonFig. 16stop bLockbaseSTOP BLOCKSee Figures 15 -16.The stop block is included with the table

18ASSEMBLY WARNING:Make sure the spindle lock button is not engaged before reconnecting saw to power source. Never engage spindle lock button when bl

19ASSEMBLY Tighten blade bolt securely. Replace the lower blade guard and blade bolt cover. Replace blade bolt cover screw and tighten securely.

2 Introduction ...

20ASSEMBLYFig. 21vIew oF MIter tabLe sQuare wIth Fence MIter Lock pLateMIter Lock handLesLIdIng MIter FenceMIter tabLethroat pLateFraMIng sQuareNOTE:

21ASSEMBLYSQUARING THE BLADE TO THE FENCESee Figures 25 - 28. Unplug the saw. Pull the saw arm all the way down and engage the lock pin to hold th

22ASSEMBLYscaLe IndIcatorFig. 28MIter scaLeIndIcator screwbeveL scaLeSQUARING THE BLADE TO THE MITER TABLESee Figures 28 - 31. Unplug the saw. Pul

23OPERATIONWARNING:Do not allow familiarity with product to make you care-less. Remember that a careless fraction of a second is sufficient to inflict

24OPERATION Release the miter lock plate.NOTE: You can quickly locate 0°, 22-1/2° left or right, and 45° left or right by releasing the lock plate

25OPERATION The 45° triangle on the miter fence provides for the maximum clearance required for adjusting the miter saw’s angle when makin

26OPERATION Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side agai

27OPERATION4 PITCH OF SIDENUMBER OF SIDES0°6M- 45.00°B- 0.00°5°10°15°20°25°30°35°40°45°50°55°60°65°70°75°80°85°90°578 910M- 36.00°B- 0.00°M- 3

28OPERATIONWhen setting the bevel and miter angles for compound miters, remember that the settings are interdependent; changing one angle changes t

29OPERATIONwrongWARNING: To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material again

3GENERAL SAFETY RULESWARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fir

30ADJUSTMENTSWARNING:Before performing any adjustment, make sure the tool is unplugged from the power supply. Failure to heed this warning could resul

31MAINTENANCEWARNING:When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product

32LUBRICATIONAll of the bearings in this product are lubricated with a sufficient amount of high grade lubricant for the life of the unit u

33NOTES

• SERVICENow that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service

4GENERAL SAFETY RULES NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes. INSPECT TOOL CORDS PERIO DIC

5 NEVER hand hold a workpiece that is too small to be clamped. Keep hands clear of the cutting area. NEVER reach behind, under, or within three

6SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of

7SYMBOLSThe following signal words and meanings are intended to explain the levels of risk associated with this product.DANGER:Indicates an imminently

8EXTENSION CORDSWhen using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to h

9GLOSSARY OF TERMSNon-Through CutsAny cutting operation where the blade does not extend completely through the thickness of the workpiece.Push