SAVE THIS MANUAL FOR FUTURE REFERENCEOPERATOR’S MANUAL10 in. Compound Miter SawTS1344LG - Double InsulatedYour miter saw has been engineered and manuf
10 — EnglishFEATURESKNOW YOUR COMPOUND MITER SAWSee Figure 1.The safe use of this product requires an understanding of the information on the tool and
11 — EnglishFEATURESMITER LOCK HANDLESee Figure 2.The miter lock handle securely locks the saw at desired miter angles.POSITIVE STOPS ON MITER TABLEPo
12 — EnglishLOOSE PARTSWARNING:The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.The followi
13 — EnglishASSEMBLYFig. 7MOUNTING SURFACE BASETRACE HOLES AT THESE LOCATIONS FOR HOLE PATTERNTRACE HOLES AT THESE LOCATIONS FOR HOLE PATTERNWARNING:
14 — EnglishASSEMBLYFig. 8Fig. 10TO LOOSENMITER LOCK HANDLETO TIGHTENDUST BAGEXHAUST PORTBASEWORK CLAMPMITER LOCK HANDLESee Figure 8.To install the mi
15 — EnglishINSTALLING BATTERIES FOR LASERSee Figure 11.Remove screw from battery compartment cover using the Phillips end of the supplied blade wre
16 — EnglishASSEMBLYTO INSTALL / REPLACE THE BLADESee Figures 13 - 14.WARNING:A 10 in. blade is the maximum blade capacity of the saw. Never use a bla
17 — EnglishASSEMBLYWARNING:Make sure the spindle lock button is not engaged before reconnecting saw into power source. Never engage spindle lock bu
18 — EnglishASSEMBLYFig. 17Fig. 18VIEW OF BLADE NOT SQUARE WITH FENCE, ADJUSTMENTS ARE REQUIREDVIEW OF BLADE NOT SQUARE WITH FENCE, ADJUSTMENTS ARE RE
19 — EnglishASSEMBLYSQUARING THE BLADE TO THE MITER TABLESee Figures 19 - 22. Unplug the saw. Pull the saw arm all the way down and engage the loc
2 — English Introduction ...
20 — EnglishOPERATIONWARNING:Do not allow familiarity with tools to make you care-less. Remember that a careless fraction of a second is sufficient to
21 — EnglishOPERATION Rotate the control arm until the pointer aligns with the desired angle on the miter scale. Tighten the miter lock handle sec
22 — EnglishOPERATION Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the w
23 — EnglishOPERATION Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the w
24 — EnglishOPERATION4 PITCH OF SIDENUMBER OF SIDES0°6M- 45.00°B- 0.00°5°10°15°20°25°30°35°40°45°50°55°60°65°70°75°80°85°90°578 910M- 36.00°B-
25 — EnglishOPERATIONWhen setting the bevel and miter angles for compound miters, remember that the settings are interdependent; changing one angle ch
26 — EnglishOPERATIONWARNING: To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material ag
27 — EnglishADJUSTMENTSWARNING:Before performing any adjustment, make sure the tool is unplugged from the power supply. Failure to heed this warning c
28 — EnglishADJUSTMENTSDANGER:Laser radiation. Avoid direct eye contact with light source.WARNING:Use of controls or adjustments or performance of pro
29 — EnglishMAINTENANCEWARNING:When servicing, use only identical replacement parts. Use of any other parts can create a hazard or cause product damag
3 — EnglishGENERAL SAFETY RULESWARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric
OPERATOR’S MANUAL10 in. Compound Miter SawTS1344LG - Double Insulated99000075010-9-13 (REV:01)• SERVICENow that you have purchased your tool, should a
4 — EnglishGENERAL SAFETY RULES INSPECT TOOL CORDS PERIODICALLY. If damaged, have repaired by a qualified service technician at an authorized servi
5 — EnglishSPECIFIC SAFETY RULES NEVER reach behind, under, or within three inches of the blade and its cutting path with hands and fingers for any
6 — EnglishSYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these s
7 — EnglishEXTENSION CORDSWhen using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capaci
8 — EnglishGLOSSARY OF TERMSNon-Through Cuts (table saws and compound sliding miter saws)Any cutting operation where the blade does not extend complet
9 — EnglishFEATURESPRODUCT SPECIFICATIONSBlade Arbor ................ 5/8 in.Blade Diameter ....
Commentaires sur ces manuels