Ryobi C2600 Manuel de l'opérateur

Naviguer en ligne ou télécharger Manuel de l'opérateur pour Coupe-circuit universel Ryobi C2600. Ryobi C2600 Operator`s manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 19
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté4.8 / 5. Basé sur13 avis des utilisateurs
Vue de la page 0
SAVE THIS MANUAL FOR FUTURE REFERENCE
OPERATOR'S MANUAL
14 in. (356 mm) Abrasive Cut-Off
Machine – Model C2600
THANK YOU FOR BUYING A RYOBI ABRASIVE CUT-OFF MACHINE.
Your new cut-off machine has been engineered and manufactured to Ryobi's high standards for dependability, ease of
operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
CAUTION: Carefully read through this entire operator's manual before using your new machine.
Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your machine properly and only for
what it is intended, you will enjoy years of safe, reliable service.
Please fill out and return the Warranty Registration Card so we can be of future service to you.
Thank you again for buying Ryobi tools.
Vue de la page 0
1 2 3 4 5 6 ... 18 19

Résumé du contenu

Page 1 - Machine – Model C2600

SAVE THIS MANUAL FOR FUTURE REFERENCEOPERATOR'S MANUAL14 in. (356 mm) Abrasive Cut-OffMachine – Model C2600THANK YOU FOR BUYING A RYOBI ABRASIVE

Page 2 - TABLE OF CONTENTS

Page 10ADJUSTMENTSWARNING:To prevent accidental starting that could cause possibleserious personal injury, assemble all parts to your cut-offmachine b

Page 3 - RULES FOR SAFE OPERATION

Page 11015304515450ADJUSTMENTSFig. 6ADJUSTABLE FLIP FENCESee Figure 6.The adjustable flip fence is located at the rear of your cut-offmachine. As ment

Page 4

Page 12ADJUSTMENTSFig. 9QUICK LOCK-RELEASE LEVERSee Figures 9 and 10.The quick lock-release lever engages the vise clamp to beused along with the fenc

Page 5

Page 13015ADJUSTMENTSFig. 11DEPTH STOPThe depth stop limits the wheel's downward travel. Itallows the wheel to go below the machine base enoughto

Page 6 - ELECTRICAL

Page 1415450MATERIALTO BE CUTPOWER SUPPLYBefore operating your cut-off machine, check your powersupply and make sure it meets the requirements listed

Page 7 - UNPACKING AND LOOSE PARTS

Page 1515450OPERATIONCUT-OFFSee Figures 14 and 15.A cut-off is made by cutting across the width of theworkpiece. A straight crosscut is made with the

Page 8 - FEATURES

Page 16MOUNTING HOLESYour cut-off machine should be permanently mounted to afirm supporting surface such as workbench. The four boltholes that secure

Page 9

Page 17Fig. 17WARNING: To ensure safety and reliability, all repairs — with theexception of the externally accessible brushes — shouldbe performed by

Page 10 - ADJUSTMENTS

Page 18TROUBLESHOOTINGPROBLEM CAUSE SOLUTIONMotor does not reach full speed or 1. Voltage from power source is low. 1. Request a voltage check from

Page 11

972000-683 6-00RYOBI AMERICA CORPORATION1424 Pearman Dairy Road Anderson SC 29625Post Office Box 1207 Anderson SC 29622-1207Phone 1-800-525-2579RY

Page 12

Page 2TABLE OF CONTENTS Table Of Contents ...

Page 13 - OPERATION

Page 3RULES FOR SAFE OPERATIONThe purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and theexplanations

Page 14

Page 4RULES FOR SAFE OPERATIONSafe operation of this power tool requires that you read andunderstand this operator's manual and all labels affixe

Page 15

Page 5RULES FOR SAFE OPERATIONWARNING: Wheel coasts after turn off. NEVER USE IN AN EXPLOSIVE ATMOSPHERE.Normal sparking of the motor or sparking fro

Page 16 - MAINTENANCE

Page 6EXTENSION CORDSUse only 3-wire extension cords that have 3-prong ground-ing plugs and 3-pole receptacles that accept the tool's plug.When u

Page 17 - TROUBLESHOOTING

Page 7Your abrasive cut-off machine has been shipped completelyassembled. Remove all loose parts from the carton. Remove the packing materials from

Page 18

Page 8FEATURESKNOW YOUR ABRASIVE CUT-OFF MACHINESee Figures 2 and 3.Before attempting to use your machine, familiarize yourselfwith all operating feat

Page 19 - Model C2600

Page 901530Fig. 3LOWERWHEEL GUARDUPPERWHEEL GUARDMACHINE ARMLOCK-ONBUTTONRUBBER FEETCARRYING HANDLEMACHINE BASESWITCH TRIGGERVISE CLAMPPOWER CORDQUICK

Commentaires sur ces manuels

Pas de commentaire