Ryobi RE180PL1 Manuel d'utilisateur télécharger pdf (Page 12)

ADJUSTMENTS

■ Lock plunge lock lever to position cutter at "zero"

depth of cut.

■ Adjust hex nuts until they come in contact with stop

flange. This will provide a position stop at “zero”

depth of cut.

■ Make sure the hex nuts are securely tightened against

each other.

■ Rotate depth stop to desired position, loosen lock

knob and adjust stop bar until it touches depth stop.

■ Slide zero-reset indicator up or down the scale on

stop bar until red line on zero-reset indicator aligns

with a desired reference point. For example, align

red line with 1 in. (25.4 mm) mark on the scale.

■ Lift stop bar to obtain desired depth of cut.

For

example, if setting 1/8 in. (3.2 mm) depth of cut, the

zero-reset indicator will move 1/8 in. (3.2 mm) from

the 1 in. (25.4 mm) reference point.

■ Tighten lock knob securely.

■ Position your router so that the cutter can extend

below the subbase for desired depth setting.

See

Figure 7.

■ Unlock plunge lock lever.

■ Grasp handles and lower router until stop bar con-

tacts depth stop.

■ Lock plunge lock lever to position cutter at desired

depth of cut.

OPTIONAL DEPTH CONTROL KNOB

An optional depth control knob is available and may be

purchased for use with your plunge router. We recom-

mend its use when your routing needs require precise

depth of cut adjustments and when router is mounted

upside down on a UL listed router table. NOTE: The

weight of the router plus the awkward position it is in when

mounted to a router table make it very difficult to set depth

of cut simply by turning the hex nut with a

15/16 in. (23.8 mm) wrench. Therefore, we recommend

that you purchase and use a depth control knob for

situations mentioned above as well as other similar

situations.

The optional depth control knob is spring loaded against

hex nut to prevent router motor from accidently sepa-

rating from router base. If depth control knob is turned

too far up depth adjustment rod, the spring will cause

depth control knob to pop off before hex nut. Do not

remove hex nut. It should remain on depth adjust-

ment rod at all times. This is especially important when

using router upside down on a router table.

TO INSTALL OPTIONAL DEPTH CONTROL KNOB

See Figure 8.

■ UNPLUG YOUR ROUTER.

WARNING:

Failure to unplug your router could result in acciden-

tal starting casuing serious injury.

■ Remove upper hex nut from depth adjustment rod.

NOTE: This is the only time you should remove the

hex nut from the router. Also, if you remove the

optional depth control knob for any reason, you must

reinsall the hex nut before reusing the router.

■ Turn remaining hex nut counterclockwise until 1/4 in.

(6.35 mm) of thread is remaining at the top of the

depth adjustment rod.

■ Place compression spring on top of hex nut as shown

in Figure 8.

■ Place optional depth control knob on top of com-

pression spring and align tabs on depth control knob

with flats on hex nut.

■ Compress spring by carefully pushing down on top

of depth control knob.

■ Thread depth control knob clockwise onto depth ad-

justment rod.

WARNING:

Relacing optional depth control knob without com-

pression spring could result in depth control knob

and hex nut vibrating off depth adjustment rod. This

situation could cause motor to separate from router

base, resulting in possible serious injury.

Fig. 8

OPTIONAL DEPTH

CONTROL KNOB

STOP

FLANGE

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 23 24

Commentaires sur ces manuels

Pas de commentaire

Ryobi RE180PL1 Manuel d'utilisateur Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Routeurs Ryobi RE180PL1