Ryobi HP41L Manuel d'utilisateur télécharger pdf (Page 9)

9 — English

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use

clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken or

destroy plastic which may result in serious personal

injury.

ADJUSTING TORQUE

See Figure 3, page 11.

There are twelve torque indicator settings located on the

front of the screwdriver.

 Rotate adjustment ring to desired setting, aligning num-

ber on adjustment ring with arrow on housing.

• 1 - 2 For driving small screws

• 3 - 4 For driving screws into soft material

• 5 - 7 For driving screws into soft and hard

materials

• 8 - 9 For driving screws into hard wood

• 10 - 11 For driving large screws

• For full power applications

DIRECTION OF ROTATION SELECTOR

(FORWARD/REVERSE/CENTER LOCK)

See Figure 4, page 11.

The direction of bit rotation is reversible and is controlled

by a selector located above the switch trigger. With the

screwdriver held in normal operating position, the direction

of rotation selector should be positioned to the left of the

switch trigger for forward motion. The direction is reversed

when the selector is to the right of the switch trigger.

Setting the switch trigger in the OFF (center lock) position

helps reduce the possibility of accidental starting when not

in use.

CAUTION:

To prevent gear damage, always allow the collet to

come to a complete stop before changing the direction

of rotation.

To stop the screwdriver, release the switch trigger and allow

the collet to come to a complete stop.

NOTE: The screwdriver will not run unless the direction of

rotation selector is pushed fully to the left or right.

TO LOAD/RELEASE BITS

See Figure 5, page 11.

The SPEEDLOAD +™ SYSTEM on the screwdriver is a quick

change chuck designed to accept any 1/4 in. hex bits. Insert

the bit into the chuck and push as far as possible until the

chuck locks onto the bit. To remove a bit, push rubber collar

forward, and then pull the bit straight out of the chuck.

LED WORKLIGHT

See Figure 6, page 11.

The screwdriver has a built-in LED worklight. This feature is

convenient when working in close or tight areas where

additional light is needed. Whenever the switch trigger is

depressed, the LED worklight will illuminate.

NOTE: During normal operation, if the LED worklight will not

illuminate, charge the screwdriver.

OPERATION

MAINTENANCE

Only the parts shown on the parts list are intended to be

repaired or replaced by the customer. All other parts should

be replaced at an Authorized Service Center.

BATTERIES

This product is equipped with a lithium-ion rechargeable

battery. Length of service from each charging will depend

on the type of work you are doing.

The battery in this product has been designed to provide

maximum trouble-free life. However, like all batteries, it will

eventually wear out.

To obtain the longest possible battery life, we suggest the

following:

 Remove the product from the charger once it is fully

charged and ready for use.

For product storage longer than 30 days:

 Store the product where the temperature is below 80°F.

 Store the product in a “discharged” condition.

NOTE: RECYCLING INFORMATION AND FIGURES (ILLUSTRATIONS) START ON PAGE

10 AFTER FRENCH AND SPANISH LANGUAGE SECTIONS.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Ryobi HP41L Manuel d'utilisateur Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Logiciel Ryobi HP41L