Ryobi HP53L Manuel d'utilisateur télécharger pdf (Page 6)

6 — English

ADJUSTABLE TORQUE CLUTCH

This screwdriver is equipped with an adjustable torque clutch

for driving different types of screws into different materials.

The proper setting depends on the type of material and the

size of screw you are using.

ADJUSTING TORQUE

See Figure 5, page 8.

There are twenty-four torque indicator settings located on

the front of the screwdriver.

 Select the gear train setting to high (Position 2) or low

(Position 1) speed.

 Rotate the adjusting ring to the desired setting.

• 1 - 4 For driving small screws (Position 1 or 2)

• 5 - 8 For driving screws into soft material

(low speed - Position 1))

• 9 - 12 For driving screws into soft and hard

materials (low speed - Position 1)

• 13 - 16 For driving screws into hard wood

(low speed - Position 1)

• 17 - 24 For driving large screws

(low speed - Position 1)

NOTE: During use, if the screwdriver stalls and begins to

make a clicking sound, and the LED worklight pulses on

and off, you should release the switch trigger immediately.

This indicates that you have overloaded the tool. Depress

the switch trigger again to resume operation.

To avoid this situation, avoid forcing the tool and refer to

the settings described above to be sure you are using the

screwdriver for its intended application.

LED WORKLIGHT

See Figure 6, page 8.

The built-in LED worklight is convenient when working in close

or tight areas where additional light is needed. Whenever the

switch trigger is depressed, the LED worklight will illuminate.

OPERATION

DIRECTION OF ROTATION SELECTOR

(FORWARD/REVERSE/CENTER LOCK)

See Figure 2, page 8.

The direction of bit rotation is reversible and is controlled

by a selector located above the switch trigger. With the

screwdriver held in normal operating position, the direction

of rotation selector should be positioned to the left of the

switch trigger for forward motion. The direction is reversed

when the selector is to the right of the switch trigger.

Setting the direction of rotation selector in the OFF (center

lock) position helps reduce the possibility of accidental

starting when not in use.

NOTICE:

To prevent gear damage, always allow the collet to

come to a complete stop before changing the direction

of rotation.

To stop the screwdriver, release the switch trigger and allow

the collet to come to a complete stop.

NOTE: The screwdriver will not run unless the direction of

rotation selector is pushed fully to the left or right.

TWO-SPEED GEAR TRAIN

See Figure 3, page 8.

The screwdriver has a two-speed gear train designed for low

(Position 1) or high (Position 2) speeds. A slide switch is

located on top of the screwdriver to select the speed setting.

When using screwdriver in the low speed range (Position 1),

speed will decrease and unit will have more power. When

using screwdriver in the high speed range (Position 2), speed

will increase and unit will have less power. When drilling use

1/4 in. hex shank drill bits only. Maximum drill size is 1/4 in.

Use the high speed setting to drill holes, and use the low

speed setting for driving screws.

WARNING:

Battery tools are always in operating condition. Lock

the switch when not in use or carrying at your side,

when installing or removing the battery pack, and when

installing or removing bits.

TO LOAD/RELEASE BITS

See Figure 4, page 8.

The SpeedLoad+™ System is a quick change chuck

designed to accept any 1/4 in. hex bits. Insert the bit into

the chuck and push as far as possible until the chuck locks

onto the bit. To remove a bit, push rubber collar forward,

and then pull the bit straight out of the chuck.

1 2 3 4 5 6 7 8 9 10 11 ... 23 24

Commentaires sur ces manuels

Pas de commentaire

Ryobi HP53L Manuel d'utilisateur Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Logiciel Ryobi HP53L