Ryobi P635 Manuel d'utilisateur Page 12

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 44
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 11
12 — English
MAINTENANCE
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result
in fluids entering your eyes resulting in possible serious
injury.
MAINTENANCE PROCEDURES
NOTE: Always remove the battery pack from the unit before
attempting a service operation.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, penetrating
oils, etc., come in contact with plastic parts. Chemicals
can damage, weaken, or destroy plastic which may result
in serious personal injury.

See Figures 16 - 20, page 17.
When you’ve finished your project and are ready to store
the backpack unit and accessories, a thorough cleaning and
lubrication is recommended.
NOTE: A five gallon bucket is recommended for cleaning
the roller and the hoses. Recommended cleaning solutions
are warm water for latext products and Klean-Strip
®
White
Formula Paint Thinner for oil-based products. When finished,
properly discard all used cleaning solution.
Place the motor switch in the reverse position and allow
to run for about 30 seconds. This will allow excess paint/
stain to be recirculated from the tubes and the sprayer
or roller back into the tank.
Remove the battery pack from the backpack unit.
Remove the lid from the tank.
Remove the tank from the backpack unit.
Return any unused paint or stain to its original container.
Fill the tank with lukewarm water (following the use of latex
products) or Klean-Strip
®
White Formula Paint Thinner
(following the use of oil-based products).
Reinstall the tank and replace the lid. Make sure the
intake tube and filter are pushed down to the bottom of
the tank.
Install the battery pack in the backpack unit.
If you were using the sprayer, spray the solution onto
a piece of cardboard or other scrap material. Continue
spraying until all the solution is used. Then disconnect the
DC power cord from both the sprayer and the backpack
unit.
If you were using the roller, remove the roller from the
roller headHold the roller head over the bucket and pull
the trigger, allowing the cleaning solution to flush through
the roller head and into the bucket.
Turn off the unit and remove the battery pack.
Remove the lid from the tank and remove the tank from
the backpack unit.
Fill the bucket with the cleaning solution determined by
the last type of paint or stain used.
NOTE: Use this bucket to clean each part of the machine
as it is removed.
Disconnect all paint tube(s) and hoses from the backpack
unit and sprayer or roller.
Clean all tubes, hoses, connections, and accessories us-
ing the cleaning brush and appropriate cleaning solution
in the five gallon bucket.
NOTE: For a thorough cleaning, remove the connections
from each end of the paint supply tube and clean each
piece separately.
Allow all pieces to completely dry before reinstalling parts
and storing the unit.

Remove the installed spray tip by turning it counterclock-
wise.
Remove the atomizer valve assembly.
Remove the locking nut by turning it counterclockwise.
Slide the pump housing assembly forward off the sprayer.
Pull the piston and spring off the pump housing.
Using the cleaning brush provided and the solution de-
termined by the last type of paint or stain sprayed, clean
all of the above parts thoroughly.
NOTE: Make sure to scrub thoroughly inside the pump
housing opening so that no paint or stain material is left
behind.

Place a line of lubricant on the piston.
Slide the spring back onto the piston.
Insert the piston and spring assembly inside the back of
the pump housing.
Replace the pump housing assembly into the sprayer.
Replace the locking nut on the motor housing by pushing
in while rotating clockwise to secure.
Insert the atomizer valve assembly into the pump housing
front opening.
Vue de la page 11
1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 43 44

Commentaires sur ces manuels

Pas de commentaire